Showing posts with label angel. Show all posts
Showing posts with label angel. Show all posts

Saturday, 23 March 2013

E21 Retrofit Angel Eyes! [Single headlight models 315, 316, 318]

I fitted CCFL [cold-cathode fluorescent tube] angel-eye rings to my E39 5-series a while back and it was pretty straight-forward, so I thought I'd have a go at a real retrofit and stick some in the E21... because all Beemers should have angel-eyes right? I know it's not a stance thing, but it is a style thing nonetheless and you don't see many E21s with angel-eyes. Twin headlight models share lamps with the E30, so the aftermarket world is your oyster, but there are no kits available for the single headlight E21 so I bought the bits separately. I bought two 145mm CCFL-rings and inverter-ballasts from car-mod-shop-ltd on eBay, which worked out about the same price as a kit @ £10 for each ring and £5 for each ballast. 

The difference of course between retro and modern cars is the headlights nowadays are usually multiple lamps fitted into a cluster, which can be easily popped open and clipped back together, making it easy to fit the CCFL-rings inside them. Classic cars, say pre 1990, tend to have separate single lamps that have fully sealed lenses and cracking these babies open without busting the glass is what gave me the most trouble on this job, so bear this is mind before undertaking it yourself and be careful, it's not something I would want to do again anytime soon! 


1. Headlight Stripping:

Exploded headlight diagram on RealOEM.com to reference parts and construct: [http://www.realoem.com/bmw/showparts.do?model=1712&mospid=47166&btnr=63_0023&hg=63&fg=05]

1a. Remove the front grilles and headlights - see this guide if you need help doing that - [http://www.blogger.com/blogger.g?blogID=3344522564318790310#editor/target=post;postID=2422546919882957928]


1b. Free the spring-clip arms from the wiring-connector and rotate them back, then pull off the wiring-connector / covering-cap and remove the bulb / sidelight-bulb + holder.

1c. Remove the tensioning spring from the headlight chassis.

1d. Use a flat screwdriver to carefully pop the legs of the adjusting-screws out of their collars on the front of the headlight chassis.


1e. Carefully tilt the rear chassis away from the lens against the plastic mounting-clip, being careful not to snap it, until the chassis is clear of the spring-clip/lens and can be rotated a quarter-turn and removed from its mount.

1f. If the headlight has one, gently prize off the thin metal cowl from around the rim of the lens. [One of mine had it, one didn't.]


2. Opening the Lens:

2a. Leave the glass lens in a very low-heat oven for 10-15 minutes to soften the sealant between the glass and reflector.

2b. Score away as much of the sealant from around the rim of the glass as possible using a square-cut razor-blade and pick it out using a small flat screwdriver.

2c. Gently push a small flat screwdriver into the gap between the glass and the metal rim. Gently rotate the screwdriver to carefully prize the metal rim away from the glass and completely crack the seal, repeating around the entire circumference of the lens.

**Make sure you take time to pick away as much sealant as possible and can see or hear it crack away from the edge when prizing with the screwdriver before trying to lift the lens - it won't take much to crack the glass!**

2d. Place the end of the screwdriver beneath the edge of the glass and gently prize it up out of the metal lens. This will likely need doing in a few different spots before the glass becomes free enough to lift out of the lens.


3. Angel-Eye Fitting:

3a. Clean the lens and inside surface of the glass.

3b. Locate a suitable position for the CCFL angel-eye ring just inside the bowl of the lens. The larger 145mm rings I'm using have a flat section along the top that meets the bonnet shut-line on E46 etc. and I thought it would make too big a gap in my round lenses, so I mounted mine with the flat spot offset 45  degrees inwards on either side, giving it a sort of badboy-bonnet look, or that's the idea anyway.

3c. Push the socket and wires from the CCFL ring trough the sidelight hole in the lens [the socket may need one of the lugs cutting off the side to fit through], locate a suitable position for the two wires in the lens with the shortest path from the ring and attach them along the flat plastic side of the ring and to each other using clear-tape.

3d. Attach the CCFL angel-eye ring just inside the bowl of the lens using clear-sealant or the sticking-pads supplied with most CCFL-rings.


4. Resealing and Fitting:

4a. Apply clear-sealant [I just used multi-purpose silicone stuff] around the metal rim of the lens and replace the glass. If you haven't marked the position of the glass, the two hooks that fasten the spring-clip down is the top of the lens.

4b. Gently prize the edge of the metal rim back toward the glass and run another bead of sealant around the outside of the rim and leave it to set.


4c. Replace the headlight bulb and holder.

4d. Drill a hole of about 8-9mm in the covering cap, just to the right of the curved contact from the original sidelight. Pop the socket and wires from the CCFL-ring through the hole and replace the covering-cap.

4e. Use a bit more sealant on the hole where the CCFL-ring wires come through the cap.

4f. Replace the metal cowl [if it has one] and prize it back tight around the edge of the glass and lens.

4g. Reassemble the remaining headlight chassis by first inserting the plastic-lug and rotating the chassis back into place. Then drop it flat enough against the lens to easily get the spring back into place and stretch the chassis back until you can pop the ends of the adjusting-screws back into their collars.

4h. Refit the headlights and grilles to the car.

5. Wiring Up:

5a. Find a suitable place to mount the CCFL-ballast where there is plenty of room for the wires to reach and affix it with the provided sticking-pads. [If you're only running a single headlight it's worth heavily insulating the unused CCFL socket and tape it out of the way - they carry a high current and can short out very easily, I've burnt out a few inverters before just by them contacting the body for a second or two!]

5b. Chop the lower of the 4 wires on the headlight wiring-connector. This is the one that sticks out further away from the other 3 terminals on the connector and should be Gy/Wt for O/S and Yl/Bk for N/S on European single-headlight model E21s.

5c. Connect the cut wire to the terminal on the CCFL-ballast's red wire using solder or crimp-connectors and insulate with heat-shrink ideally, or tape.

5d. Connect the black wire from the CCFL-ballast to the headlight earth-wire - the brown wire on both sides. You could do this by soldering or with a multi-crimp connector, but I found the easiest way was to bend the metal terminal of the black wire 90 degrees and slide it into the brown wire socket on the headlight connector. The connector then holds the wire tight when it's pushed into place. A bit slapdash, but it does the trick!

5e. Plug the wiring connector back into the headlight and connect up the CCFL-ring to the inverter-ballast.


Enjoy your new angle eyes!


Sunday, 6 February 2011

E39: Fitting CCFL 'Angel Eye' Headlights

Always wanted to get a set of these for my old 3 Series, but never managed in the end, so it seems like a worthy first mod for the 5. I'm sure you've seen the Angel Eye rings on modern BMWs and for older models without them you can buy whole replacement light clusters [£100+], or CCFL kits, which are rings that fit into you're existing headlight lenses. The latter are much cheaper, but they're fiddly to fit. They are approved by BMW though and are European E-Marked, so they're totally road legal. They were about £50 when I had my E36, so I'm glad to see they've nearly halved in a couple of years and I scooped mine from lightspeed_123 on eBay for £27.99 delivered! A bargain for the high-quality and finish of the kit - even the packaging was posh.




The kit didn't include any instructions though and it gets quite tricky fitting them, so after a lot of web trawling I managed to find some instructions for a similar kit fitted on a 3 Series, but with only limited references to the E39 5 Series. It served as a starting point, but with no dedicated guide for E39 readily available I've decided to jump straight out of the ScoobyLab into the fire, with my own How-To guide.

REMOVING THE HEADLIGHT:

1. Remove the 5 wiring-loom sockets from the back of each headlight.

2. Remove the 4 screws holding the light-cluster in place, located on the slam-panel and down the back of the cluster, using an 8mm wrench.

3. Pull the light-cluster forward from the inner side until the lug on the outer corner can be slid out and the cluster removed.

4. Slide off the strip of body-coloured trim and rubber seal from the bottom of the headlight.

FITTING THE RINGS/INVERTERS:

5. Remove the back of the headlight to expose the lenses by lifting the 6 clips with a screwdriver - 3 along the bottom, 2 on top and 1 on the inner edge, the last one is between the outer edge and the back of the corner-indicator - then gently prize the headlight apart.

6. Place the CCFL rings into the front part of the headlight and secure them with tape temporarily. Apply a blob of clear silicone-sealant to each end of the rings and another at the bottom. [If you're rings are one-sided, like ours, make sure the metal side is facing inwards.]


7. Connect the rings to the inverter by clipping the wires together.

8. Using glue, or sticky-pads if they come with your kit, secure the inverter box into the gap at the inner end of the headlight.

9. Run the 4 wires along the top of the glass and loop the rest round in the gap with the inverter until nothing is overhanging, then secure them with tape.


10. When the sealant has dried, remove the tape holding the rings and clip the back of the headlight back into place. Run the Red/Black wires from the inverter box through the drain plug on the inside corner of the headlight back, by removing the rubber drain spout, feeding the wires through the hole and then the spout as you replace it.

11. Replace the rubber seal and strip of body-coloured trim.


WIRING INTO THE EXISTING SIDELIGHTS:

12. Cut the wires to the sidelight socket and strip the ends. This is the plug with 2 round female sockets - the wires are Brown (-) and Grey (+) w/ a Blue stripe on O/S, Brown stripe N/S.

13. You'll need about 8" of wire reach from the drain-spout, so if necessary extend the Red/Black wires. [I just added two lengths of Blue/Brown 240v wire, used blue crimp-connectors to join them and sealed them with heat-shrink tube.]


14. Slide the two wires from the headlight through the 3mm hole on the edge of the radiator nearest the top and reverse the headlight removal procedure. Pull the wires from the inverter tight through the hole as the headlight is slid into its mount.


15. Connect the wires from the inverters to the sidelight wires using crimp-connectors or solder, then seal them with heat-shrink tube or electrical-tape. Plug the 4 remaining sockets back into the headlight and cover the old sidelight socket on the headlight with elec.- tape.


** It'll take about 60 seconds for the rings to reach full brightness the first time they're switched on.

Phew, a long process then, but worth it for the looks and the age it takes off the car I'm sure you'll agree!