1988 E30 318i Project - Check List:

 I will update this and cross things off as progress is made:

• Straighten steering wheel.
• Speedometer / Odometer inop.
• Temperature gauge inop. [THIS POST]
• Washer-jets / pump.
• No hot air from heater-blower. [THIS POST]
• Central locking malfunction.
• Instrument lights flicker / dimmer function inop.
• Clock inop. [THIS POST]

ENGINE:

• Rough idle / stalling when cold. [THIS POST]
• Exhaust too loud. [THIS POST]
• Clutch slave-cylinder leaking.

BODYWORK:

• Paint NSF wing.
• Repair rear valance.
• Touch up valance corners.
• Panel above rear lights.
• OSR wheel arch.

E30 318i [M40]: Massive air leak SOLVED - lower inlet-manifold gasket

I had checked and re-checked the idle control valve [ICV], the air-flow meter [AFM], ignition system, tested for the fuel pressure, performed tests on the DME [ECU] to make sure that was working and even laboriously tested the wiring loom for continuity, but still the engine idles terribly when cold. It ticks over lumpy, shakes the engine side to side and cuts out at will, even when power is applied. 

I checked the timing and all was good, under the rocker-cover showed no defective valves and the cam-shaft doesn't look all that worn. I guess the only thing left to check is the injectors... right?? Now hold on a minute I hear the E30 and M40 engine gurus cry, the symptoms you've described point towards an obvious massive air leak in the induction system! 

This is true and is also the very first thing I looked for and tested. Initially I performed the 'spray' test using a can of brake-cleaner (though 'Easy-start', carb-cleaner or electrical-cleaner work too, anything with alcohol content). This involves running the engine and spraying brake-cleaner around the intake-manifold, ICV, vacuum hoses, throttle-body etc. If unwanted air is being sucked in, say through a split hose, the brake-cleaner will be sucked in and combusted by the engine causing it to rev higher. If you are spraying in one particular place and the engine revs increase accordingly then you have found your air-leak. Thing is, I did this test over and over again and it showed nothing. 

I’ve heard that air can be sucked in past the injector bodies when the rubber sealing rings have degraded over time and that the lower intake-manifold is also a main culprit, but spraying round this area made no difference to the engine revs or affected the poor idle. I did a compression test and the readings were a bit low, but not enough to cause any issues.

At this point I decided it to bite the bullet and begin stripping things down. The removal of the lower intake-manifold is quite complicated because it involves removing the fuel-lines from the rail, which is why I put it off, but clearly if you want to fix something then you need to get your hands dirty so off came the fuel lines and away came the lower manifold to reveal.... well, as you can see from the photo, a virtually non existent gasket. Sigh. 

Cylinder 1 has a massive gap where the gasket is no longer there, so whenever there is a vacuum in the plenum it’s just filling up with fresh air even with the throttle-body shut and this explains why the ICV appears to be doing nothing and leads people to look there first. Whoever was refitting the manifold was obviously in a rush because the broken gasket has folded over on itself, causing the air gap to be even bigger. I guess they just tightened it hoping to make a seal, but alas no. Cylinder 2 is not much better with a noticeable gap and the rest of the gasket squashed flat. Cylinders 3 and 4 are better, but still paper thin. It looks like this may be the original gasket and the past 35 years have not been kind to it (or to me for that matter).

So... looks like I have found the culprit of the rough idle. Finally! New gasket is ordered, a snip at £6.88! Amazing how such a simple thing can cause such a severe problem and goes to show how sensitive these ‘analog’ ‘80s cars are to air metering issues!

E30 318i: Correct Temperature Sensor fitted (Brown Plug) + wiring/loom issue

The temperature gauge in the dash has not worked since I bought the E30, which was a little worrying on my 250 mile drive home, but the car does not overheat. Oh, it has some issues with the cooling-system, like the heater-matrix pipes fitted incorrectly and an air-lock at the back of the head, but hey it doesn't overheat. Still though, I thought it best to get the bottom of the faulty temp. gauge for peace of mind, particularly with summer coming / just about here.

The M40 has two separate temperature sensors that are independent from one another. The temperature gauge works from the 'Brown plug' sensor to the rear of the head [right in pic]. The forward sensor is the 'Blue plug' [left in pic] and that connects only the DME (ECU) to tell the car if the engine is cool or warm to help with cold-start procedures. A single sensor cannot be used for both purposes on these older engines as the resistance value ranges required for each function differ, the DME being a digital circuit and the temp. gauge still working in analog. [You can read more about this on the E30 Zone Wiki HERE].

MULTIMETER TESTING:

The temp. sensors can be easily tested with a multimeter set to 20k ohms resistance. 

The Blue plug is a two-pin sensor, so test across both terminals with the multimeter and you are looking for a reading of 4-4.5k ohms for a working sensor. This sensor and plug can be accessed easily without removing any parts from the engine.

The Brown plug though will require removal of the lower inlet-manifold to access the sensor for testing or replacing. This is a single pin sensor, so place one probe of the meter to the terminal and the other to a ground-point in the engine bay or against the block/head. Expect a reading of between 1k and 1.5k ohms for a working sensor. To test the Brown plug sensor without removing any parts from the engine, you can apply the multimeter to Pin 4 of the C101 connector (main wiring loom plug in engine bay) which is easy enough to get at, or at Pin 26 of the blue connector to the right side of the instrument binnacle, though the binnacle will need removing to do this.

WRONG SENSOR / CONFUSING WIRING LOOM:

All M40 engine wiring looms use a single pin temp. sensor on the brown plug that earths through the engine block and have only a single wire in use leading to it. Some looms, using components destined for other BMW models, are known to have a second wire leading to the Brown plug temp. sensor which is redundant on the M40 motor, though this is rare and seen more often on 6-cyl. M20 looms. My car has one such loom, however and I realise that this is what has caused confusion in the past and led to the wrong sensor in fact being fitted...

Upon inspection, the rear temp. sensor fitted to my E30 is black, not brown and has two terminals. The second pin means that the sensor body earths back to the loom and not through the block so, if the redundant earth wire in my loom is not connected to a ground-point then the sensor was open circuit. I guessed that someone had ordered a second Blue plug sensor by mistake and fitted that, but it turns out the part number doesn't match and the sensor is for a completely different model engine entirely. The reading from the multimeter was over 11k ohms, something like 7.5 times what it should be! That sensor was never going to work with the E30 temp. gauge circuit whether it was earthed or not.

I ordered the correct single-pin sensor with the brown base from mr-wiper on eBay, who also supplied my Bosch spark-plugs. It was only £7.69 delivered. My temp. gauge now works, but this may also be due in part to removal of an air-lock at the back of the head due to a heater-matrix problem so coolant is now flowing properly round the area of the sensor. 

A BIT MORE ON WIRING LOOMS:

Brown / Violet, brown being the main colour, denotes that the power source provided from the temp. gauge circuit is earthing through this wire and does not need to be a closed circuit back to the gauge. The other wire is either not wired in to the loom or goes to a body-earth anyway, so earthing the sensor through the block will make no difference. This colour coding is the same for all wires in all BMW looms, I would imagine most cars are the same.

E30 318i: Noisy exhaust gets a bung / silencer

My E30 has a 4" straight-through Japanese tuner style exhaust back-box fitted, which to the say least is LOUD. In fact, it's one of the loudest I've heard on any car, including a Subaru turbo I had with a de-cat pipe. I figured the centre-box had also been removed from the E30, given the noise level, but find it is still there under the car and looks to have been replaced not too long ago, so I guess the only reason for the volume from this 1.8 litre 4-banger is because it never had a catalytic converter from the factory and is subject to no emission controls that bind (and quieten) modern cars. This E30 is 1988, so must have been right at the end of this phenomena.

While the loud pipe might be fun on a jaunt, working on the engine at home I find myself needing to start and idle the car constantly for testing and this is where the noise causes a problem, mainly with my neighbours and passers-by. They tolerated it for a couple of weeks, but with a few running problems that are still being ironed out and the car unable to move to another location I decided to try and mute it a bit. 

I had two options. Buy a more sociable back-box or get a silencing 'bung' for the current one. I'm not best pleased with look of the Jap-style straight-cut end pipe, I mean I like them but don't feel it suits the boxy E30 and though I'm down with car style juxtapositions all DAY, this isn't the one I would have chosen, so first looked for a replacement. New stock items are not expensive, but too much for this project, so second hand was the way, with twin 'sports' style spurious back boxes and used OEM items going for between £50 and £100. I was tempted by a nice twin square pipe from a German tuner, but the seller had no idea how loud it was and at £55, I still deemed it too pricey at this uncertain stage in the project. People at work fit ‘bungs’ to their motorbikes so I thought this was budget way to reduce the burble by a few dB.

DOES IT WORK?

Yes and no. It certainly takes the edge off the noise level, that ‘crack’ has gone, but it’s still one loud exhaust. The info says it reduces sound levels by up to 15 decibels and I have adjusted to the quietest, most restrictive setting, but without a dB meter I can’t really say if it is that much. In my opinion it’s not to that great an extent but it is somewhat quieter. 

Don’t expect the exhaust to sound as quiet as a stock back box with baffle plates. I suppose you’re never going to get a quiet exhaust tone and still enjoy the slight increase in power a straight-through pipe gives, so as ever there is a compromise, but it has certainly done the trick for me of making the car less anti-social when tuning it in my driveway! Who knows, when I get the E30 out and about over the summer the bung may well be coming back out.

E30 318i M40: Bosch injectors and tips - checking condition

Next on the agenda to find the culprit of the rough running and stalling idle was to examine the injector condition and the plastic tips. The injector bodies are quite rusty and corroded so they could well be the original set, but on closer inspection the tips are fine and they look to be in pretty good condition, so onwards.

To inspect the injectors the lower inlet manifold will need to be removed, which involves de-plumbing the fuel lines and some of the water hoses. 

E30 318i M40: Camshaft and valve condition

I whipped the rocker cover off to check if there was a dropped valve or broken spring that might be contributing to the poorly idle, but no such defect found. In fact, this has to be one of the cleanest top ends I have ever seen. Nice!

BMW E30: Digital Clock quick LED upgrade

The bulb had blown in my E30’s digital clock, so I decided to repair it with a quick and easy LED upgrade. It’s another bulb load of power taken off my 35 year old dash wiring so can’t hurt. 

The bulb-holder is integral to the working of the lamp, with the metal clips that hold it in place also acting as live/earth contacts. LEDs built into such a holder can be purchased specifically for replacing bulbs like this if you want to go that route, but if you have a bunch of cheap LEDs lying round and don’t want to spend any money then read on.

Simply remove the plastic holder and cut the old bulb away from the two pieces of metal. Solder a cheap yellow or red LED onto the metal contacts in the place where the bulb was attached and bend the LED stalks back on themselves so the diode is pointing the right way, as in pic. A pure-white LED would probably be better, but they use more wattage, will probably require a spend and cheaper dome LEDs work fine anyway.

The bulb for the clock has a resistor built in anyway, so the LED will run fine and not pop without modification, but if you find it is too dim or bright to you can ‘piggy-back’ another resistor across the stock one to raise or lower resistance to suit. A calculator to help work out what resistance you need are easily available online, but trial and error is best if you have a bunch of LEDs / resistors lying round.

You may want to cover the recess at the back of the clock with electrical tape to stop light spilling out.