Surprisingly the manifold nuts all came off as they should this time and left all eight studs in the head... weird, but it certainly made fitting the gaskets a lot easier.
|
Showing posts with label compression. Show all posts
Showing posts with label compression. Show all posts
Saturday, 16 February 2013
E21 316: More manifold gaskets for M10...
Stuck the new and much better quality exhaust-manifold gaskets on today from Euro Car Parts. They're thicker than the eBay ones and have steel rings round the inner rim like a head-gasket, should make a better seal. It's got rid of the cracking noise from that dodgy one on cyl. 4 [this post] and the engine sounds sweeter than ever.
Surprisingly the manifold nuts all came off as they should this time and left all eight studs in the head... weird, but it certainly made fitting the gaskets a lot easier.
Surprisingly the manifold nuts all came off as they should this time and left all eight studs in the head... weird, but it certainly made fitting the gaskets a lot easier.
Sunday, 10 February 2013
E21 316: M10 Engine cured! - Culprit: manifold gasket...
After repeatedly timing the ignition perfectly to Z on the flywheel, [see this post], we decided there had to be something deftly wrong to be causing the loud noise and backfiring [in the vid below], rather than just the distributor being out of line.
The first hunch was the exhaust had broken while being twisted to get the cylinder-head out and was blowing like mad, but my initial inspections revealed no damage to the down-pipe or manifold and the four manifold gaskets looked all to be in position.
That is to say they LOOKED in position... Today, in the pouring rain, I got the car up on ramps to see what it was I'd missed and as soon as the torch flicked on I could see the answer at last - one of the exhaust-manifold gaskets had slipped off the stud and was only covering half the hole! Nightmare... Right at the back of the engine where we couldn't see and, ironically, the one for cylinder 4 that started all the trouble.
As you can see the gasket has been totally blown apart by the hot exhaust and has separated quite badly in the middle leaving only the metal. I checked the rest of the gaskets in my set for a spare, but can only find the same shape gasket with an oblong hole, perhaps for the E28, so tentatively decided to re-use the blasted one, correctly seated this time and caked in Holt's FireGum.
As soon as the engine fired up again it sounded like it used to. It's amazing the difference that gap in one single exhaust port made to the noise level. It was still idling low though and revving badly, so I grabbed the timing-light again to have another go, turning the distributor to line up Z on the flywheel - 25 degrees before TDC. Now the 30 year old M10 has really begun to purr once more. Awesome! Still some fettling to do on the carb. tuning, throttle/choke cables and checking to see if my damaged manifold-gasket is holding up, but at least she's back on the road after a tense month!
The first hunch was the exhaust had broken while being twisted to get the cylinder-head out and was blowing like mad, but my initial inspections revealed no damage to the down-pipe or manifold and the four manifold gaskets looked all to be in position.
That is to say they LOOKED in position... Today, in the pouring rain, I got the car up on ramps to see what it was I'd missed and as soon as the torch flicked on I could see the answer at last - one of the exhaust-manifold gaskets had slipped off the stud and was only covering half the hole! Nightmare... Right at the back of the engine where we couldn't see and, ironically, the one for cylinder 4 that started all the trouble.
As you can see the gasket has been totally blown apart by the hot exhaust and has separated quite badly in the middle leaving only the metal. I checked the rest of the gaskets in my set for a spare, but can only find the same shape gasket with an oblong hole, perhaps for the E28, so tentatively decided to re-use the blasted one, correctly seated this time and caked in Holt's FireGum.
As soon as the engine fired up again it sounded like it used to. It's amazing the difference that gap in one single exhaust port made to the noise level. It was still idling low though and revving badly, so I grabbed the timing-light again to have another go, turning the distributor to line up Z on the flywheel - 25 degrees before TDC. Now the 30 year old M10 has really begun to purr once more. Awesome! Still some fettling to do on the carb. tuning, throttle/choke cables and checking to see if my damaged manifold-gasket is holding up, but at least she's back on the road after a tense month!
Monday, 14 January 2013
E21 316: M10 Misfire Woes:
Went on a Maccies run with some work colleagues on New Year's Eve and I may have been pushing the old girl a bit hard, when a horrible clanging noise began from the engine and got worse quickly. Some of the guys at work suggested the first stop should be the rotor-arm and dizzy-cap so we managed to get some delivered through the parts dept. that afternoon, but it was still chugging on a mixture of cylinders and it limped home for me then refused to start again. When it eventually did the old M10 barely managed to fire 3 cylinders.
My list of diagnostic checks was:
Replaced distributor-cap and rotor-arm.
Tested all 4 plug-leads.
Replaced all 4 spark-plugs.
Removed, cleaned and rebuilt Weber carb.
Checked valve-clearances and confirmed all valves appear to be moving correctly, turning the engine by hand.
Finally diagnosed cylinder 4 as no firing.
Plug and lead tested again, this time sparking against the suspension turret.
Compression test revealed Cyl. 1 and 2 @ 150psi, 3 @ 45psi and 4 @ 25psi.
This all seems to point to a bust head-gasket between the 3 and 4 cylinders. It is unlikely the valves for 2 cylinders would have bent or suddenly need adjusting at the same time, so off with its head and lets look at that gasket.
*UPDATE: The head came off pretty quickly and revealed one seriously blown head-gasket right between the 3rd and 4th cylinders [detailed pics in this post]. Diagnosis spot on, but the culprit may be a slight warping at that end of the alloy-head - not very much at all, but still a worry considering it looks to have been skimmed before. Either way, the new head-gasket is on [I went for a full head set off eBay for £27.99, which includes the manifold gaskets etc.] and the car is running on all four cylinders again, though not as happily as it could be. I was forced to remove the distributor and seem to be having some issues with ignition timing since putting it back [in this post], and the carb. still hasn't been tuned properly since the rebuild, so a range of fettling awaits before I can drive it for the first time in 2013.
My list of diagnostic checks was:
Replaced distributor-cap and rotor-arm.
Tested all 4 plug-leads.
Replaced all 4 spark-plugs.
Removed, cleaned and rebuilt Weber carb.
Checked valve-clearances and confirmed all valves appear to be moving correctly, turning the engine by hand.
Finally diagnosed cylinder 4 as no firing.
Plug and lead tested again, this time sparking against the suspension turret.
Compression test revealed Cyl. 1 and 2 @ 150psi, 3 @ 45psi and 4 @ 25psi.
This all seems to point to a bust head-gasket between the 3 and 4 cylinders. It is unlikely the valves for 2 cylinders would have bent or suddenly need adjusting at the same time, so off with its head and lets look at that gasket.
*UPDATE: The head came off pretty quickly and revealed one seriously blown head-gasket right between the 3rd and 4th cylinders [detailed pics in this post]. Diagnosis spot on, but the culprit may be a slight warping at that end of the alloy-head - not very much at all, but still a worry considering it looks to have been skimmed before. Either way, the new head-gasket is on [I went for a full head set off eBay for £27.99, which includes the manifold gaskets etc.] and the car is running on all four cylinders again, though not as happily as it could be. I was forced to remove the distributor and seem to be having some issues with ignition timing since putting it back [in this post], and the carb. still hasn't been tuned properly since the rebuild, so a range of fettling awaits before I can drive it for the first time in 2013.
Subscribe to:
Posts (Atom)