E30 318i: Water in rear footwell - windscreen cowl leaking? Koi carp anyone??

After heavy rain I noticed the rear passenger foot well in the E30 is full of water. Can't see any signs of water ingress through the door seals or any stains in the headlining, but am told a common cause of this is the windscreen-cowl, so will be looking into this soon. For now, I have drilled a nice drain hole so at least it won't be filling up again.

When a roof falls on a 4 Series...

As if the aftermath of the high winds across the UK this weekend was not bad enough with roof tiles downed and half my barbecue making its way over to next door's garden, I was then called to one of our sites this morning to help lift the forecourt roof off of a customer's 2016 425d...

The bonnet/hood took the brunt, but the rear window has smashed too and, considering nothing hit the glass directly I would assume that just the shock of the massive impact to the front of the car caused it to shatter. Must have made quite a bang...

Considering the size and weight of the metal awning that collapsed I think the Beemer took it pretty well... car is atill driving ok... still, I wouldn't like to be the member of our Service department who had to call the customer this morning and tell them...

E39: Replacing / Unclogging the Washer-Jet Pump

If you think your pump is faulty then check this post first - Windscreen Washer-Jet System Problem.

-----------------------------------------

Removing the pump is easy, but getting to it is quite involved due to the amount of under-car panelling the E39 has.

PROCESS:

1. Jack up the o/s front of the car and detach the plastic mud-guard by removing the 3 hex-head screws that hold it to the wheel-arch. using a 7mm wrench.

2. Lift off the plastic under-tray that sits to the rear of the wheel-arch by removing the 5 plastic-studs around its edge. If you lack a took for pulling out this kind of stud then lever the head of the centre-pin out a few mm with a flathead screwdriver and then slide it clear with pliers. The body of the stud should now slide out easily.

* The car may need lowering to remove the under-tray and re-lifting, as the jacking-point lies in the centre of it.

3. Remove the 7 hex-head screws around the inside of the wheel-arch. as well as two at the leading edge of the under-tray, unseat the inner wheel-arch from around the lip of the wheel-arch itself and pull the plastic inner-arch down out of the way.

* The water-tank for the windscreen and headlight washer-system is located just behind the wheel-arch, below the front of the driver's door. Not the Intensive cleaning-system, which has both the tank and pump under the bonnet.

4. Unplug the wire-connector from the pump in centre of the tank**, by sliding a flat screwdriver into the clip and lifting it upwards.

5. Pull the slim hose-connector clear of the central pump** and allow the tank to drain.

This is a good point to test the washer system one last time to make sure it isn't a blocked hose and the pump is getting no water.

6. Gently twist and pull the pump upwards about an inch out of its mount, then remove the black rubber-bush it sits in.

7. Flush the tank several times by pouring water into the filler-nozzle under the bonnet and allowing it to drain through and clean around the lip of the pump-mount. Check the pump for clogging.

8. Replace the rubber-bush to the tank and, using the new pump if necessary, reverse the procedure.

** The pump in the centre of the tank with the slim hose is for the windscreen washers. The left-hand pump with the larger hose is for the headlight washers.

*** The black connector on the inner corner of the tank is the level-indicator probe. This is also a push fit and the best place to drain from, after removing the wire-connector as above.

E39: Windscreen Washer-Jet System Problems

Replacing / Unblocking the Pump - How to Guide: http://www.planet5.co.cc/2011/10/replacing-unclogging-washer-jet-pump.html

I've had a couple of minor faults with the windscreen/headlamp washer jet and they look like they could be common to most E39 models.

1. Disconnected/Broken Nozzle Hose:

Fault Finding: One washer-nozzle is not working at all / only emitting a tiny amount of water, while the other remains functional.

The hoses for the windscreen-washer run up the offside bonnet-hinge and along the back of the bonnet to reach the nozzels. Due to the constrictive nature of the plastic crimp-clips used to hold them in place, the hoses can be stressed while the bonnet is repeatedly opened and shut. This will most likely cause the plastic-connector to become unplugged from the nozzle [as with my car] so it's just a case of snapping the two connectors back together. The hoses could also be caused to split, so if the connectors are still in place then operate the system and check for leaks along the hose. You will probably need a replacement hose if it is split, unless it is near enough to the nozzle to chop off the split section and reseat it. If there is no leak then it is likely that the hose has been crimped shut, so check each plastic crimp-clip attaching it to the bodywork and adjust it so there's no restriction.

If you suspect you have this problem then check it over as soon as possible as there will be water/screenwash pouring down the back of the engine every time you use the washer system!!

2. Blocked / Faulty In-Tank Pump:

Fault finding: Both wash-jets are not emitting water, or emitting a small amount of water then stopping. No sound can be heard from the washer-jet pump, or the pump is very loud and appears to be struggling to get water through.

If there is no sound from the washers then, if the fuse hasn't blown, its likely the pump is dead and needs replacing. If the pump appears to be struggling but not pumping water then first unclip the hose at the join located under the bonnet, half way down the lip of the driver's wing and try the washers. If water isn't getting this far then a blocked hose/nozzle can be ruled out and the pump will need removing and replacing to unblock.