BMW DPF cleaning - guerrilla style! [All Diesel BMW, F10 530d]

When your DPF is blocked and the car won't perform a re-gen, then chances are a good highway thrashing is not going to solve the problem any more and the DPF will have to come off to be properly cleared of clogged up soot. Replacements are outrageously expensive and professional cleaning is not cheap, plus the DPF must be sent away, but it is possible to do at home for very little money. You just need a suitable place to do it and be prepared for the mess...

A guide on removing the DPF for F10/F11 is here.

1. Compressed Air Blowout - This is the first step we took and may be all that is necessary if the DPF is not completely blocked. The only way I've seen so far with air compressed at enough pressure to clear stuff from the DPF is to use a 'bead-blaster' or 'bead-seater' designed for blowing tyres on wheel rims at about 90 psi. I doubt a tyre-shop is likely to let you use their equipment to blast a load of soot out of a DPF, as it is messy business, but if you know someone or have access to one then it's very effective. The DPF needs clearing out backwards, so secure it to the floor somehow (or get someone wearing ear-defenders to put their foot on it) and aim the bead-blaster into the flexi-pipe leading to the exhaust.

2. Cleaning Solution - This is a much deeper clean than just blowing the DPF out and will take a couple of days with it removed from the car.

• Seal the front end of the DPF as water-tight as possible. Re-fit the sensors to their holes and block off the small metal tube. Use thick plastic material to seal the large front opening of the DPF, tied tightly around the rim. Chances are it will still leak some liquid from around this aperture.
• Obtain suitable DPF cleaning-solution. I first used Wynn's Professional Off-Car DPF Cleaner, which cost me £27 for 5L. Quite pricey, but it certainly does the job. The Wynn's solution does smell very similar to a couple of cleaning products that were already available to me at work, both made by Autosmart, but I'm sure other companies make similar - TFR (Truck Film Remover), a strong de-greasing and cleaning solution, and G101, a very strong soap solution, so if you have access to these products it may be cheaper to get a few litres of each of them instead. I ended up using about 5 litres of neat TFR and the same amount of neat G101 after most of the Wynn's had leaked away and we have since cleaned out the DPF from an E81 120d, which worked a treat.
• Place the DPF in a bucket and leave the solution to soak into the DPF over at least 12, but preferably 24 hours. Even if it is impossible to stop fluid leaking from the DPF, the bucket will fill to a level where the pressure equals out and the DPF can be fully filled with solution as long as you have enough.
• Remove the plastic and jet-wash the DPF out from back to front, with the lance into the exhaust outlet. Be careful where you do this as it is very messy, with a lot of thick black soot being ejected, so try and do it directly down a drain as it cover a large area if done onto the ground. If you do not have access to a pressure-washer, then you could try flushing it with buckets of water poured in quickly, but this is not going to be as effective.
• Rinse the remaining soap from the DPF by leaving a hose to run through it and / or pouring buckets of water through. This will minimise the car 'blowing bubbles' once the DPF is refitted and still has soap / moisture inside!
• Leave the DPF to drain and dry out for as long as possible and refit it to the car.
• Give the car a 'spirited' highway drive, preferably in 3rd gear if it is manual, to blast remaining loose debris from the DPF. If the car was showing error codes for the DPF only and these have been reset, at this point the car should begin to re-gen by itself.

BMW F10/F11: Clogged/blocked Washer Pump Filter - EASY FIX / FILTER REMOVAL! [E90/E92/F07/F30 etc.]

Windscreen washer jets not working, but the pump can still be heard OK? Then you have a very common case of clogged filter. Due to the supposed inaccessibility of the bottle on later model BMWs I have read stories of high dealer bills, daunting inner-wing removal and even back-feeding the washer-hose with bleach to gradually unblock the gunged up filter... but before you try this read on, as it is an easy fix after all.

GUIDE:

1. Fully turn the steering to the right to give access behind the driver's front wheel to work. [Removing the wheel will give more access but is not necessary.]

2. Remove the 6 screws holding securing the rear half of the felt wheel-arch liner in place using an 8mm socket. This will allow access without removing the arch-liner completely. Four of the screws are located in the wheel well itself and two are located underneath next to the sill.

3. Remove the plastic 'mud-guard' trim on the outside of the wheel-arch that adjoins the felt arch-liner. This is done by pressing the centre-pin of the 3 plastic clips through the clip and then removing the clips with a panel-popper tool. [It may be possible to do the job without removing this trim piece, as the clips are very hard to get out and prone to breaking, but visibility and access are certainly improved].

4. Peel the felt wheel-arch liner out from the rear lip of the wheel-arch and if possible tuck it behind the wheel. The washer-bottle should now be visible to the rear of the front wheel. It sits in a tight gap between the outer and inner wings of the car body itself and access is very limited. [This is unlike E39, E60 etc. where the bottle sits left-to-right across the rear of the wheel-arch and access if much easier!]

5. Remove the windscreen washer hose from where it enters the pump and move it out of the way.

6. Slide a long flat-screwdriver in between the washer-bottle and the outer wing and prize the pump upwards until the spout is clear of the bottle and the pump can wedged up and out of the way.

7. The clogged filter should now be sitting in the washer-bottle where the spout of the pump fits. Use the flat-screwdriver to prize the filter up and out of the bottle. It should now be removable by hand or using long-nose pliers / tweezers.

8. Clean the gauze filter using water and lightly brush it with a sponge-scourer or stiff brush. [I find an old toothbrush works perfectly.] It is likely clogged with a 'gel' like substance that builds up supposedly due to the use of incorrect washer-fluid as well as dirt from the bottom of the tank if the washer has been run without fluid in for a while, but should clean up pretty easily.

9. Carefully slot the filter back into the washer-bottle and press it back into place using long-nose pliers / flat screwdriver or both, making sure it is fully seated.

10. Slide the pump spout back into the filter / washer-bottle, making sure it is fully seated and rotated to the correct position with the spout for the windscreen-hose pointing to the side of the car.

11. Refit the washer-hose, trim, wheel-arch liner and wheel. [Reverse steps 1-5.]


www.e90post.com/forums/showthread.php?t=930107
http://www.bimmerfest.com/forums/showthread.php?t=737416
http://forum.bmw5.co.uk/topic/120732-f10-windscreen-washer-not-working/
http://forum.bmw5.co.uk/topic/124943-f10-washer-problems/

E39: Replacing / Unclogging the Washer-Jet Pump

If you think your pump is faulty then check this post first - Windscreen Washer-Jet System Problem.

-----------------------------------------

Removing the pump is easy, but getting to it is quite involved due to the amount of under-car panelling the E39 has.

PROCESS:

1. Jack up the o/s front of the car and detach the plastic mud-guard by removing the 3 hex-head screws that hold it to the wheel-arch. using a 7mm wrench.

2. Lift off the plastic under-tray that sits to the rear of the wheel-arch by removing the 5 plastic-studs around its edge. If you lack a took for pulling out this kind of stud then lever the head of the centre-pin out a few mm with a flathead screwdriver and then slide it clear with pliers. The body of the stud should now slide out easily.

* The car may need lowering to remove the under-tray and re-lifting, as the jacking-point lies in the centre of it.

3. Remove the 7 hex-head screws around the inside of the wheel-arch. as well as two at the leading edge of the under-tray, unseat the inner wheel-arch from around the lip of the wheel-arch itself and pull the plastic inner-arch down out of the way.

* The water-tank for the windscreen and headlight washer-system is located just behind the wheel-arch, below the front of the driver's door. Not the Intensive cleaning-system, which has both the tank and pump under the bonnet.

4. Unplug the wire-connector from the pump in centre of the tank**, by sliding a flat screwdriver into the clip and lifting it upwards.

5. Pull the slim hose-connector clear of the central pump** and allow the tank to drain.

This is a good point to test the washer system one last time to make sure it isn't a blocked hose and the pump is getting no water.

6. Gently twist and pull the pump upwards about an inch out of its mount, then remove the black rubber-bush it sits in.

7. Flush the tank several times by pouring water into the filler-nozzle under the bonnet and allowing it to drain through and clean around the lip of the pump-mount. Check the pump for clogging.

8. Replace the rubber-bush to the tank and, using the new pump if necessary, reverse the procedure.

** The pump in the centre of the tank with the slim hose is for the windscreen washers. The left-hand pump with the larger hose is for the headlight washers.

*** The black connector on the inner corner of the tank is the level-indicator probe. This is also a push fit and the best place to drain from, after removing the wire-connector as above.

E39: Windscreen Washer-Jet System Problems

Replacing / Unblocking the Pump - How to Guide: http://www.planet5.co.cc/2011/10/replacing-unclogging-washer-jet-pump.html

I've had a couple of minor faults with the windscreen/headlamp washer jet and they look like they could be common to most E39 models.

1. Disconnected/Broken Nozzle Hose:

Fault Finding: One washer-nozzle is not working at all / only emitting a tiny amount of water, while the other remains functional.

The hoses for the windscreen-washer run up the offside bonnet-hinge and along the back of the bonnet to reach the nozzels. Due to the constrictive nature of the plastic crimp-clips used to hold them in place, the hoses can be stressed while the bonnet is repeatedly opened and shut. This will most likely cause the plastic-connector to become unplugged from the nozzle [as with my car] so it's just a case of snapping the two connectors back together. The hoses could also be caused to split, so if the connectors are still in place then operate the system and check for leaks along the hose. You will probably need a replacement hose if it is split, unless it is near enough to the nozzle to chop off the split section and reseat it. If there is no leak then it is likely that the hose has been crimped shut, so check each plastic crimp-clip attaching it to the bodywork and adjust it so there's no restriction.

If you suspect you have this problem then check it over as soon as possible as there will be water/screenwash pouring down the back of the engine every time you use the washer system!!

2. Blocked / Faulty In-Tank Pump:

Fault finding: Both wash-jets are not emitting water, or emitting a small amount of water then stopping. No sound can be heard from the washer-jet pump, or the pump is very loud and appears to be struggling to get water through.

If there is no sound from the washers then, if the fuse hasn't blown, its likely the pump is dead and needs replacing. If the pump appears to be struggling but not pumping water then first unclip the hose at the join located under the bonnet, half way down the lip of the driver's wing and try the washers. If water isn't getting this far then a blocked hose/nozzle can be ruled out and the pump will need removing and replacing to unblock.