F10/F11: DPF Replacement / Removal - EASY GUIDE!

If you are removing your DPF and re-mapping, or if your filter is clogged past the point of a re-gen, then you will need take it off. Getting the DPF / catalytic-converter off an F10 is easier than it looks and is totally doable at home without a set of workshop ramps. I managed with a jack / axle-stand and without removing the exhaust or any of the engine.

1. Safely raise the car.

2. Under the car, remove the centre under-tray that covers the exhaust joint to the DPF by undoing a series of 8mm screws.

3. Loosen the collar-bolt at the joint between the front section of the exhaust and the flexi coming from the DPF using a 14mm socket.

4. Slide the exhaust back about an inch until it pops out of the sleeve in the DPF. [It may help here to pop the exhaust out of the centre rubber-hanger to give more rearward movement.]

5. Under the bonnet, unplug the two O2-sensors and the Lambda sensor, then pull the hose off the metal-tube that runs to the pressure-sensor. Free up the wiring.

6. Remove the upward-facing O2-sensor using a 14mm open-ended wrench.

** Access to the bolts and sensors may be easier with the plastic air-inlet loosened and moved out of the way. **

7. Loosen the collar-bolt joining the front of the DPF to the back of the turbo using a 13mm socket on a long extension and move the collar forward away from the DPF.

8. Remove the upper nut and lower bolt holding the bracket to the rear of the DPF using a 13mm wrench.

9. Remove the two bolts holding the bracket to the back of the engine-block using an E10 double-hex socket, or an 8mm ring-spanner and fully remove the bracket.

10. The DPF will likely be solid in place, so the best bet is to wiggle it from underneath car until it breaks free and can be safely lowered down.

11. With the DPF free, getting it out of the engine-bay is still not a walk in the park. The lower O2 sensor and/or Lambda sensor may need to be removed to get the angle required to slide the body of the DPF down past the steering-knuckle and foil heat shield, which may need to pressed in towards the body a bit to give enough clearance. Eventually, the DPF can be manipulated down through the gap and drop down under the car, so watch out if you have it raised a fair bit off the ground.

12. Re-fitting is a reverse of the above steps. Note, all but the lower O2-sensor should be fitted after the DPF is secured in position. The easiest way to reposition the DPF is get someone to hold it from below high enough for you to get hold of it from inside the engine-bay and lift it up into position, rather than one person trying to reposition it from underneath.

F10 / F11: Front Bumper Removal Guide

** If you are removing / replacing only one side headlight, then it is possible to loosen the bumper on the corresponding side and peel it back to access the headlight screws, rather than removing the entire bumper. **

1. Under the bonnet/hood remove the front end of the rubber seal located just inside the front wings either side.

2. Remove the two plastic push-pin type fasteners on each top corner of the bumper skin. (Or just the ones on the side you are removing the headlight on.)

3. Remove the 4 screws holding the top edge of the bumper using a T30 Torx socket.

4. Under the car, remove the 8 screws under the bottom lip of the bumper using an 8mm socket.


5. There are 3 screws located at the forward side of each front wheel-arch that need removing using an 8mm socket, locations pictured. (If you are working on one side/headlight then these screws only need removing on the corresponding side, as with steps 6 and 7.)


6. Peel the plastic wheel-arch liner back from the corner of the bumper and wedge it against the tyre.

7. Remove the 2 screws located on the inside of the bumper on each side that can now be accessed with the arch-liner out of the way, as pictured. The near one needs a 10mm socket, the one further in is another 8mm. A 1/4" drive wrench is good here with not much room.

8. Gently pull the bumper outwards from its bracket until it separates from the front wing and pull that side of the bumper forward. It should peel away from the car quite easily. Repeat for the other side and the bumper is off, unless you are only working on one side as the headlight and other parts inside / behind the bumper are accessible with one side pulled away from the car.

9. If you are completely removing the front bumper, remember to unplug the front fog-lamps, parking-sensors etc. before moving the bumper away from the car. There is plenty of room to do this with the O/S (right-side) bumper peeled off.


Many thanks to Isturbointeg on F10post.com for some of his superb pictures I made use of. His original guide on F10post forum is here - https://f10.5post.com/forums/showthread.php?t=1187122

BMW DIS v57 User Manual + SSS v32 User Manual [PDF]

DIS v57 User Manual:
https://drive.google.com/open?id=1vU8q_xrf3ZOAUQjagdpPx_t9kvyq__fg

---

SSS v32 User Manual:

https://drive.google.com/open?id=11HU6YZPBURp7E1gr0c8uPdBlGndgI5vV

E60 Diesel: Replace Turbo Waste-Gate [Actuator]

This is a pretty easy job and can be done with removing the turbo, exhaust-manifold or rocker cover.

1. Remove the inlet duct to the air-filter housing. It's held by a T30-Torx screw at the front and just unclips from the housing.
2. Remove the boost-pipe from the top of the turbo by removing the screw from the left side of where it joins to the turbo using a 10mm wrench, then loosening the right hand screw using a T30-Torx socket and rotating the collar clockwise until it can be pulled out of the turbo.
3. Remove the other end of the boost-pipe from the left side of the intercooler by reaching from underneath with a flathead screwdriver and sliding the metal clip down. The pipe should pop the intercooler easily and be pulled out from above. [This can be done without fully removing the engine-undertrays].
4. Gently slide the rubber vacuum-hose off the metal spout on the waste-gate.
5. Remove the three screws holding the waste-gate to the turbo using a 10mm wrench. [There is just enough room down the left side of the engine to get a ring-spanner on, otherwise a ratchet with a short extension-bar may get them more easily].
6. Push a cloth or some tissue roll down under the bottom of the waste-gate between the turbo inlet and exhaust wheels to stop the retaining-clip getting lost into the engine and slide the clip off the waste-gate arm using a long flat screwdriver. [There is just enough clearance to get an angle with the screwdriver and just about see the clip. The clip will probably have to be removed with a stick-magnet].
7. Slide the waste-gate arm off the stud and remove it.
8. Refit the new waste-gate as a reversal of above, being careful not to lose the retaining-clip during refitting. The clip may need holding in position with a stick-magnet as it is pushed down with a flat screwdriver.

E87 LCI: 1er Warning-light woes + dodgy pad-sensor. [How to reset.]

My boss Mike has been dying to get back on the Beemer wagon, so has surreptitiously gifted himself by getting his wife an E87 LCI 118d M-sport as a present. It was time to reset the service lights, which can be done using the 'trip reset' button on the clocks, like other modern BMWs, though with no iDrive the procedure is slightly different.

HOW TO RESET SERVICE DURATIONS:

1. Turn ignition on without depressing the clutch. [Key phase 2 on push-button models].
2. Hold the trip-reset [odometer] button on the clocks until a yellow triangle with ! appears.
3. Single presses of the trip-reset button will now cycle through the service menu options [service, oil, brake-pads etc.]. Stop at the one you want to reset.
4. Hold the BC button on the end of the left indicator-stalk until a clock appears next to the menu-icon on the dash. When the clock stops counting the service duration for that option is reset.

• A red icon is a service duration warning. An orange icon means it is overdue / there is a fault.
• A red/orange icon of the car in the air with a stand under it means there is a fault and it needs to go in to BMW [or get a scanner on it].
• If the handbrake light stays lit up after you release the handbrake then this means there is a fault in the brake system. If you know the discs/pads to be OK and the brakes are fine, then you have a dodgy pad-wear sensor.

PAD-WEAR SESNOR ERROR: [HANDBRAKE-LIGHT]

After resetting the brake-pad service indicator we noticed the mileage count had not reset. The icon in the service menu recommending the car be taken to a dealership [the car icon with a stand underneath] and interestingly, the handbrake light was staying on even with the handbrake released. After a bit of forum scanning it turns out the light staying on means there is a fault in the braking system or one is about to develop. This is common when pads / discs have been changed and 9-out-of-10 times it means a pad-wear sensor has been disturbed and thrown up a fault. If you know the brakes are working as they should then the warning message can be cleared with a scanner and probably wont return. If it does then a pad-wear sensor has failed [scanner will likely confirm this] and will need replacing. You can do both of them for about £10 and it's a really easy job - wheel off, 2 bolts and a push-fit - but if you're truly skint I believe there is a technique online somewhere to just twist some wires together and bypass them.

http://www.babybmw.net/forum/viewtopic.php?t=23763

http://www.e90post.com/forums/showthread.php?t=698040

E60 Diesel: Replacing the Front Turbo Housing/Volute

**The turbo needs to be removed. Reaching the 8mm nuts at the back of the volute is impossible               with it in situ.

1. Mark a line on the original volute / front-casing where each 8mm screw is located before removing it. It is adjustable and the new one needs to be in the exact same place as the original for correct waste-gate location.
2. Remove the 3 screws holding the waste-gate bracket to the turbo front-casing / volute using a 10mm wrench.
3. Remove the 6 screws holding the front-casing / volute to the turbo and wiggle it free.
4. Hold the new volute up to the original and mark lines in the corresponding places. This is best done with them on a flat surface and holding a straight-edge across both.
5. Slide the new volute on to the turbo and replace the six 8mm screws, ensuring the lines are correctly located before tightening them up. It is alloy-to-steel, so no high-heat gasket-paste is required.
6. Press the waste-gate into the right position for the bracket to meet the holes on the volute and replace the three 10mm screws holding it in place.

Why I replaced mine:

With re-con turbos starting at £350, I went for a used one from a crash damaged 7-Series. Mine is an early E60 and has the vacuum-actuated turbo, so it was handy that the 7er did too as they are hard to source - eBay is full of the electronic-actuated type and I couldn't see a vacuum one, but it may be that they are inter-changeable.

The overall condition of the turbo looked worse than the one I was removing, but there is a bit less play in the spindle-shaft so worth a shot at £200 delivered, let's hope the saving pays off. The only drawback is the front-casing was slightly damaged at the point where the pipe to the intercooler fits, but swapping the original one in was not a difficult job.

E60 Diesel: Remove/Replace Turbocharger

Removing and refitting the turbo itself is not a difficult task, but the mass of other parts that need removing to access it makes this a reasonable amount of effort.

You will first need to remove:

Engine covers. [5mm Allen]

Air inlet ducting and air-filter. [5mm Allen]

Inlet manifold. [10mm + 11mm Hex]

Injector pipes. [17mm open-end wrench]

Injectors. [8mm Hex]

Rocker cover. [10mm deep-Hex]

Turbo to intercooler pipe. [10mm Hex + T30-Torx]

Airbox to turbo pipe. [5mm Allen]

EGR to exh.-manifold pipe. [T45-Torx + 7mm Hex]

Exhaust-manifold. [10mm deep-Hex + 12mm deep-Double-Hex]

Front engine-undertray. [8mm Hex]

Engine reinforcement-plate. [16mm Hex]

Exhaust vibration-damping rods. [13mm Hex]

REMOVAL:

1. Remove the two nuts holding the down-pipe/cat to the back of the turbo using a 17mm wrench and work the down-pipe back off the studs.

2. Remove the banjo-bolt that attaches the turbo oil-feed to the block using a 14mm wrench, remove that end of the oil-feed pipe and loosely screw the banjo-bolt back in a few turns to stop any oil leaking from the block. Put some cloth against the block under the pipe to catch any drips and remove and retain the 2 copper washer-seals as they are easily misplaced.

3. Reach under the turbo, locate where the lower oil-return pipe enters the rubber-hose to the sump and loosen off the upper jubilee-clip using a 6mm-Hex socket or flat screwdriver if you can get access. Let the jubilee-clip slide down the rubber hose.

4. Slide off the rubber-hose that runs to the waste-gate on the turbo.

5. Make sure the turbo's weight is supported, remove the two bolts holding the turbo-bracket to the block using a 13mm wrench and lift the turbo out, carefully sliding the lower oil-return pipe out of the rubber-hose.

FITTING:

6. **Ensure all oil-feed pipes etc. are swapped over to the new turbo**. Lower the new turbo into position, sliding the lower oil-return pipe back into the rubber-hose and loosely refit the two bolts.
7. Tighten the jubilee-clip on the oil-return hose and refit the oil-feed hose back on to the banjo-bolt, making sure the copper-washers are in place either side.
8. Place the exhaust vibration-damping rods back in place to locate the down-pipe and loosely refit the 13mm nuts.
9. Refit the neck of the down-pipe to the back of the turbo and tighten the 17mm nuts.
10. Place the exhaust-manifold over the studs on the cylinder-head and manoeuvre the turbo into a position where the bolts holding it to the manifold can be fitted. It can be trick to do while keeping the gasket aligned. Turn the three manifold-to-turbo bolts using a 12mm deep-Double-Hex (12-sided) socket until the manifold is seated, but do not fully tighten them.
11.  Lift the turbo to take the weight off the manifold and fully tighten the two bolts holding it to the block using a 13mm wrench. They are a pain to get to but it is doable, also a lot easier with someone else lifting the turbo.
12. Replace the twelve copper-nuts that hold the exhaust-manifold to the cyl.-head and tighten them using a 10mm deep 6-sided socket, as the strip easily with 12-sided ones.
13. Tighten the three bolts holding the manifold to the turbo.
14. Re-connect the rubber vacuum-hose to the waste-gate.
15. Refit the other things on the above list.

http://www.instructables.com/id/How-to-replace-Turbocharger-on-BMW-30L-Diesel-E60E/

E60: Replacing all Brake Discs and Pads.

1. Jack car, remove wheel. REAR ONLY - ensure handbrake is off.
2. Remove plastic caps and 7mm Allen-head bolts.
3. Remove caliper and hang it from the spring.
4. *On front-N/S and rear-O/S ONLY* - Remove pad wear-sensor by gently working it up out of the slot with a small flat-screwdriver. Part of the green plastic may brake off but it's very unlikely the sensor will stop working, so provided you are careful to retain the metal clip it will fit back on tight enough.
5. Remove 18mm bolts from caliper bracket and lift out of the way.
6. Remove the stud holding the disc to the hub using a 5mm Allen-key socket.
7. Wobble the brake disc off. REAR ONLY - It may need whacking from behind with a hammer as it will bind to the handbrake shoes.
8. ** If you are replacing the inboard handbrake shoes, then do this now.
9. Fit the new brake-disc to the hub. The hand-brake may need adjusting for the drum to slide over the shoes as it self-adjusts to stay against the worn drum on the old brake-disc. It will likely need adjusting to the new drum anyway. 
10. Reverse steps 5 to 1.

Pad wear-sensors are a pain to remove.

I wangled all 4 discs and pads for £140 from LVW who supply where I work. 

Belaco are a budget make, but we fit them to vans at work and they seem OK.

Mintex pads do the job.

Plenty of meat left on the old discs, but the MOT fail showed brake imbalance.

The old pads looked alright too, but no imbalance reported on the retest.

E36 Compact: M43 Oil Change + Filter Removal.

Got round to changing the oil and filter on the Compact, as I've been running it for a month with the mayonnaise filled concoction left from the dodgy head-gasket / cooling issue.

Removing Oil-Filter:

The filter-housing on the later M43 316i / 318i is right down in the bowels of the engine and impossible to get to easily, as they are on almost all other BMWs. The lid has no nut either to undo it from above, so the only way is to use an old-skool oil-filter removal tool from the side, only most of the engine prevents this.

The simplest way to get it off is to remove the fan-cowl and fan. This way there is just about enough room at the front of the engine to get a turn on the filter with the removal tool. I found a chain based removal tool works well, but a steel-belt one would probably be just as good. It isn't essential, but I removed the top inlet-manifold too, just to see what I was doing more clearly.

1. Remove the fan-cowl by undoing the two top screws with a 10mm socket and lifting it off, popping it out from the air-inlet ducts at either side.

2. Remove the two 8mm screws holding either side of the rear edge of the fan-housing at the top and lift the fan vertically up, sliding it out of the two bottom lugs.

3. Slide the removal-tool in from the front and there should now be room enough to get a turn on the filter-housing lid, even if it's as tight on as mine was.

E46 318ci: Total Jobs Checklist.

Sat 6.7.15:

6 months tax.

2 new front tyres.

4 new brake discs.

New master-cyl. / servo.

Fuel tank repair.

Replacement front bumper.

Sat 12.7.14:

• Re-bled brakes.
• Wynn's Engine Stop-Leak and half a litre oil.
• Rad-hose repair-tape kit, cable-tie out of way, 1 litre water/coolant.
• Cleaned wiring-connectors to cam-sensors.
• Cleared all oil residue from exhaust-manifold.

Quick run of engine with NO MAF connected gives improved idle-speed of 900rpm. After revving, it drops below 900 for a moment, then returns to 900.

Brakes are bled and still very stiff. No servo assistance is present, but the servo and m/c are known to be working. Could the problem be the vacuum pump? Could this be causing the oil leak?

If not, then it feels a little too low for the rocker-cover and will most likely be coming from the rear main-seal, which is a gearbox off job, so lets hope its just draining from one of the rear rocker-cover plugs and running down the head.

Tues 15.7.14:

Replace vacuum-pump.

Replace both camshaft-sensors.

Replace MAF sensor.

Remove inlet-manifold to check CCV and crank-sensor.

Clean oil and recondition inlet-manifold.