E30 wheels is a magnificent topic of discussion, so lets have a couple of different takes on wheels for the old 3er...
By far the most common wheels to bestride the E30 are cross-wire / BBS styles. and beyond that owners tend to stick to solid period styled alloy wheels like Azev-A five-spokes or Borbet C. Personally I think the old-school BMs look best with steel-wheels such as the almighty Weller competition wheels, as in the pic above, especially with a lowered car. These are built for heavy-duty dirt-track racing and off-road and I think give a lowered E30 the best squat / rat look.
At the other end of the spectrum, here are some ultra-modern Japanese-style alloys on a 325is. I am not 100% on who makes these, but they look very much like RAYS Volk or Rota wheels. You don't see many wearing rims like these, certainly not done well anyway, but why not? Sharp lines suit sharp lines and the 3-box shape combined with large modern alloys gives the E30 a very purposeful look and go-kart stance.
Well, I've had a bit of a nightmare week. As I was replacing the front n/s shock-absorber with the new spring, ready for the MOT on Saturday, the strut-insert burst in my face. To get an extra couple of inches clearance at the top and get it under the wing I'd been pushing the damper down into the insert. I figured they sit quite far down with the short-springs anyway, but eventually, probably after doing it several times, I must have plunged it further than its full operating depth and it popped, sinking the insert completely into the strut.
You wouldn't think pushing it down would pop it, considering the forces on it under load, but once its down far enough the top seal just fails under the pressure of the oil. You can have SPAX, as with most adjustable-inserts, re-filled and the seal replaced if you can be bothered to send it back to the manufacturer and pay the cost, but with time of the essence I just bought a new one.
Larkspeed in Leeds were the cheapest, though the price had gone up from £90 to £112 [and £118 now for the shortened!] for a single insert, but they claimed to have the part in stock and would have it to me by Tuesday the latest. Today I rang them to say it'd been a full week since they rang to confirm the order and still no insert. After half an hour they rang me back to say the insert had been specially ordered from SPAX, who were now lacking correct parts and can't build them until the end of October. I wish they had told me that last week as I'm now waiting on a refund...
Bilstein - fixed damping-rate and pricey, nothing but good reviews.
I rang DC Performance.co.uk, who also claimed to have the part in stock and it would take 2 or 3 days. Before parting with any money this time I asked if they could check the insert is definitely in stock, which they are not, so it's not looking hopeful for any existing stock anywhere. I will be contacting SPAX directly from now on.
Monroe Gas-Matic - strong, but ride too soft.
So what are the short-term options? There are no ride-adjustable inserts in stock and available now, so it looks like i'm now bound to non-adjustable inserts. Stiffened Bilstein inserts are £62 each, where OEM-replacement ones can be had for as little as £20. With the springs this low, I have no idea what would work best. The sportier, better-brand damper might last longer under the stress and be a better match for the adjustable SPAX on the other side. Alternatively, the cheap, softer damper might compress better under the load and a pair will only cost £40 should the o/s one need swapping too. Another option is to replace both with Monroe gas-filled dampers for £123. The blurb says they are a heavy-duty design for trucks and vans, but according to this thread they are just too soft and will cause me to bottom out. So, £60 for one Bilstein it is, or take a chance on a cheap KYB. Hmmm, stress.
Well my MOT, the UK roadworthiness test, has come round and the E21 is just too low to get into my local testing station, let alone up onto the ramps. This is where height-adjustble coilovers would be worth their £650, as even if I can get the car onto the ramps, an attempt to raise the wheels off the ground will cause the short springs to become loose in the pans. The solution to this problem is still cheaper than coilovers - shortened strut-inserts from this post at ~£400, but I'll still have to find somewhere with ramps low enough to take her.
Seems to me the easiest and cheapest overall solution is to just swap longer springs in for the test and put the chopped ones back on later. Seems like quite a lot of effort just for a 30-minute inspection, but that's motoring in the UK, we're at the mercy of the MOT and it sees more cool cars off our overcrowded roads than insurance write-offs ever would.
Slight length difference. The red SPAX was a -40mm too.
A nice set of yellow APEX -40mm springs set me back just £80 from eBay. They are a lot longer than I remember though, which heralded me finally buying some spring-compressors, £17.99 and bringing the grand total of this years test to a ton before I've even had it inspected... not good.
Fitting the rear springs was a doddle, but the fronts threw up a few problems. Getting the cut spring off was easy enough, but even under compression the longer one was never going to fit in the space available. After damaging my newly filled wheel-arch and bursting one of my strut-inserts - nightmare - I started looking for a better guide on replacing springs and find out if it can ever be done with the strut and brake-line still attached, but one doesn't seem to exist - a good validation for this and other blogs! I did, however, find a Youtube video of some guys fitting H&R springs without removing the shock, which did give some clues from about 3min30 onwards:
PROCESS:
Rear Springs -
1. Follow the steps in THIS POST to remove and re-fit the rear shock-absorbers, swapping the cut-spring for the new ones, obviously.
Front Springs [without removing strut, steering or brake-line] -
1. Raise the car and remove the corresponding front wheel. [It makes life easier to drop the front on axle-stands and remove both wheels, doing both springs together.]
2. Undo the top-nut from the shock-absorber, located on the suspension turret under the bonnet, using a 19mm wrench and 8mm open-end spanner at the top of the strut-insert to stop it from rotating.
3. Disconnect the brake-pad sensor wire by simply pulling it apart at the join behind the disc and sliding the rubber-mount free of the bracket.
4. Remove the earth-lead from the strut by undoing the bolt with a 10mm wrench.
5. Remove the bracket holding the brake-line to the strut using a 10mm wrench and open-end spanner. [This is essential to free the brake-line enough for it to tilt forward without having to remove the hose and drain the brakes. Without freeing the bracket, the brake-line will be stretched to breaking.]
** If the spring is still under compression without the weight of the car on it, use spring-compressors to hold it short enough to loosen the top spring-pan away from the turret.
*** The strut can be tilted out far easier with the track-rods unbolted, using a 17mm wrench and moved out of the way, but mine wasn't budging easily and there is enough room if you can push the steering-arm down enough.
6. Remove the four nuts holding the anti-roll bar brackets to the sub-frame using a 17mm wrench and open-end spanner. The anti-roll bar should drop down and remove tension from the two struts.
7. Tilt the shock-absorber strut out of the wheel-arch, remove the top spring-pan and spring.
8. Drop the new spring onto the bottom pan and reverse the above steps, using spring compressors if necessary.
Wheel-arch gap a little more prominent. Was it really that much before?!
Hacking out the inner wheel-arches at the back to make the 16x9s fit left them in a right state, with a big gap up inside the wing. Being where it is, the gap is wide open to dirt and water flinging up off the wheel ready to rot the body from the inside out, so as a temporary measure I covered the area in ally-tape. It worked well, but was never going to last long. I figured the inner-arch would be considered a structural part of the body and would need a steel fillet welding in, but it doesn't appear to be the case so fibre-glass will do.
The area is a bit big for filling in though, so I shot up to Halfords and bought a square-metre of fibre-glass matting, £4.29. You need resin to apply it, which is a bit dearer. A kit is available for £9.99 that includes a small bottle of resin and a small mat, otherwise resin starts at a fiver and hardener is extra. The recommended resin is polyester-based, so it stretches, but I figure that marine epoxy-resin, which can be used for fibre-glass, will do the job as it may not be as flexible, but sure is waterproof and rock hard. I also happen to have a litre of the stuff left over from some carbon-fibre projects a few years ago.
I weighed the fibre-glass mat up to the whee-arch and cut it into rough shapes. The instructions say to coat the mat in resin and then stick it, but I found it just as easy and a little less messy to brush a little resin onto the surface, then stick the pieces of mat on dry and brush in heaps of resin over the top. The epoxy is quite thick and stiffens quickly, so this may the only workaround method using this stuff. It's certainly done the trick, the fibre-glass is as solid as the metal and has stuck well even to the rough under-seal surface, lets just hope it doesn't flex too much and crack away. It should see me through the MOT next week and that's the main thing, but at least there's no mud being flung up into the wing anymore. A quick coat of red-primer and the tester may not even notice the difference...
This is the first wheel-arch I pulled to fit the 16s and it's the only one now still needing a tidy-up, to say the least. I cut too much of the lip off trying to wedge some balloon-like 45% profile tyres and left it in a right mess. The newer 40% profile tyres fit perfectly and only needed minor cutting to the other arches, leaving this one miles from the rim and totally out of shape. The bit I cut off is the line used to form the arch on the rest, so this one was missing an edge to build the filler up to and totally sculpting the new arch-line by hand with hanging bits of mesh and filler was never going to happen. The easiest method would be a plastic arch cover, hiding the cut area completely and easily smoothed into the wing, but all four would have to match and the Group 2 ones are just too big to consider. It seems my only options are -
B. Spot-weld the piece I cut off back into place and secure it with fibre-glass filler. Fill the lip to match the others and build up and re-shape the arch up to where it meets the wing almost.
No doubt B involves a lot less time and effort, but it's still going to be a lot of rubbing down.
The chewed up scrap of metal, good job I saved it. It didn't just slot back into position, there was quite a bit of grinding and filing.
I had wanted to tack-weld the metal on and fill the gaps with fibre-glass, but I couldn't get hold of one so masking-tape did the job. I caked on plenty of P40 fibre-glass filler in between the tape, waited for it to go off, removed the tape and filled in the gaps.
Well sealed behind with more P40. You can see the sliver of metal in position as the light shines through, showing just how much arch got cut off originally.
It was then ground down with a rotary-file on the drill, mainly inside so nothing rubs on the tyre, but a bit to give the lip some shape. All that's left now is the arduous task of filling all that arch.
Been enjoying the car and weather too much over summer to neaten up the pulled wheel-arches, but thought I'd take some time off to finish them before the rain and gloom sets back in.
I bent the lip with a pair of grips into the smoothest arch I could and filled it flush with P38 to where the original outer lip was. This took quite a bit of building up.
Normally I'd give it a coat of zinc-primer for now and rub it down again, but for aesthetic value I went straight to red-primer and it's already lifted the look of the car.
More of the rear arches had to be cut away than the front, so this meant a smaller and slightly easier area to fill. The only remaining arch is the dreaded N/S rear one, which I hacked to death trying to install tyres that were too big, but it's a mammoth job alone and will have to wait.
