E30 318i: Replacing Clutch Slave-Cylinder - Quick + dirty guide!

Clutch reservoir suddenly low on fluid? Gearbox housing covered in it? Sounds like a popped slave-cylinder. Not to worry, this has to be one of the easiest to replace ever made!

* This guide covers the M40 engine and 5-speed gearbox, but process is the same for most models. *

1. Lift the left side of the car.

2. Remove the 13mm nut from the outer side of the slave-cylinder. This one is easy to access and can be got with a ring-spanner or socket, but the ratchet is quite snug to the gearbox.

3. Remove the 13mm nut from the inner side of the slave-cylinder. This is quite difficult to get to as it is inhibited by the clutch-hose as well as limited access in the trans.-tunnel. I managed it with a socket and a 4" extension bar to get past the hose/pipe. 

* I have seen someone getting that difficult to reach nut using a longer extension bar and the ratchet further back behind the gearbox, but this was not possible on my E30, so I'm guessing this may be for 4-speed boxes or older M10/M20 engines. If yours cannot be got with the details in step 3, then try this. *

4. Remove the slave-cylinder fr the gearbox and allow to hang down on the hose.

5. Clamp the hose (optional, but saves time when bleeding system later).

6. Remove the hose end from the slave-cylinder using an 11mm wrench so the old unit can be discarded. [It is much easier to grip the slave-cyl. by hand while it is removed from the gearbox and get a turn on the pipe-collar, as well as minimising leaks from the hose.]

7. Prime the new slave-cylinder by removing the bleed-nipple and carefully pouring DOT4 brake/clutch fluid into the hole at the top for the hose/pipe until the air is displaced and the fluid run out of the lower hole. It won't need much. Refit and tighten the bleed-nipple. 

8. Refit the hose-end to the slave-cylinder and remove the hose-clamp if you're using one.

9. Refit the slave-cylinder to the gearbox and tighten the two 13mm nuts.

10. Top up the clutch reservoir with DOT4 brake/clutch fluid and bleed the system of air. [Which bleeding technique you use is up to you, but for all BMW clutches I would recommend using a one-way valve attached to the bleed nipple as detailed in THIS POST, which saves time and headaches.]

E30 318i: Leaking clutch slave-cylinder... fluid low

Now the E30 is running well I took it out for a test run and noticed that all of a sudden the gears were grinding a little bit. Checked the fluid reservoir and the level had dropped to about 10mm, not good. Looked under the car and saw a spot of fluid on the drive right under the slave-cylinder. My guess, and no prizes for guessing right here, it was a leaking slave-cylinder and, hey presto... sure looks like one to me.

Replacement is ordered. I went for a cheap and cheerful one off eBay for just £16.50, though £25-40 seems to be the going rate. Be fitting this when I have chance. Looking forward to the bodywork, but mechanical jobs just keep popping up... that be old BMWs!

F10 530d: Clutch Replacement [Manual 520d, 530d, 535d, F10, F11]

The clutch on my F10 has felt like it's on the way out for about a year now and over the last month or two I've noticed it starting to slip a few times, mainly when moving off in first gear with the car pointing uphill. Time to throw a new clutch in, one of my least favourite jobs and just as with everything on the 5 Series, way more involved a process than swapping a clutch into a Ford Focus. Even I was tempted to just leave the F10 with someone to do the clutch for me, but with quotes in the £1000 - £1500 range I figured it was better to bite the bullet and do it on the drive. Just as well too, as you can see from the pics to the right just how far gone the clutch was, with hardly any face left on the friction-plate and some lovely hot spots on the pressure-plate! Nice.

I'd love to say this job is the same as the E39/E60, which are pretty straight forward, but it is trickier due to updates in the car's design. The main difference is in the prop-shaft removal, the F10 requiring the rear gearbox-mount to be removed to access the bolts to the coupling. This makes it almost impossible to move the car to rotate the prop and access the top bolts, so a bit more ingenuity is needed. I also notice that the gearbox must be lowered in order to remove the slave-clyinder, which is wedged up in the trans-tunnel, something that was not necessary on the E39 and E60. The hose to the slave-cylinder also needs to be unplugged and fluid drained so the gearbox can be lowered. This is an added annoyance that BMW have engineered in here.

** Before you undertake this job yourself, it should be understood that 5-ers are complicated cars and a lot needs to be removed before the gearbox / clutch can be accessed. This is a short list...

• Main under-tray and both side trays.
• Exhaust.
• Two heat-shields.
• Brackets.
• Rear gearbox mount and bracket on back of gearbox.
• Propshaft coupling and centre-bearing.
• Starter-motor.
• Hose to slave-cylinder. [inc. refilling and bleeding of clutch].
• Only now can you remove the gearbox and swap the clutch...

But hey, if you have made it to this guide then chances are you aren't fazed by this kind of thing! So read on... the whole job can be done at home over a weekend by yourself, taking your time and enjoying yourself... or could be done in one day by two of you...

PROCESS:

** Disconnect the battery negative-terminal and put it safely out of the way. **

1. Remove the front belly-pan under-tray located below the engine and gearbox. It is held in place by 8mm screws all around the edges and a couple in the middle.

2. Remove the left and right middle under-trays. These are located under the sill on each side and held on by a lot of 8mm screws and some plastic clips.

3. Remove the centre cross-brace by undoing the eight 13mm bolts, four on each side. This is a steel plate that runs across from left-to-right near the back of the prop-shaft.

4. Remove the exhaust up to the down-pipe. First loosen the 16mm nut on the flange connecting it to the down-pipe at the front. There are then two rubber-hangers, one next to the rear-axle and one to the front of the back-box. A third rubber-hanger is located to the front of the exhaust, not far back from the down-pipe and this can be separated on its bracket by removing the two screws using an E10 double-hex (female-torx) socket. Finally there is a 13mm nut holding a bracket at the very back, up inside the rear-bumper. The exhaust can now be carefully lowered [watching the rubber-bush that has no purpose on the right of the back-box does not get caught in the bumper], worked free of the flange on the down-pipe and fully removed. If the car is high-up on a lift then you will likely need a second person for the last bit.

5. Remove the main heat-shield located above the exhaust. It is held on by several large, flat metal nuts that can be loosened with a 10mm wrench and then spun off by hand.

6. Remove the aluminium bracket that sits around the centre-bearing of the prop-shaft by undoing the two 8mm bolts holding it to the bearing and wiggling it free.

7a. Place a jack or suitable stand under the gearbox to support it so the rear mount can be removed. 

7b. Remove the rear gearbox mount by undoing the three 13mm bolts on each side holding it to the car and a single 13mm nut in the centre that holds it to the rubber-mount on the gearbox.

8a. Remove the braided electrical-earth strap at the back of the gearbox by undoing the 13mm nut attaching it to the body.

8b. Remove the bracket at the back of the gearbox that attaches it to the rear mount, by undoing the four bolts using a T55 Torx socket. Make sure the socket has good purchase here, as it can slip out easily and round the edges of the bolt-head.

9. Remove the 3 bolts holding the prop-shaft coupling (donut) to the back of the gearbox using an 18mm wrench on either side of the nut/bolt. The bolts on the upper side of the prop-coupling are difficult to get to up in the trans-tunnel. If the rear wheels are not lifted and the prop cannot be turned to get to the bolts, it is possible to get them with CV-joint type sockets as I did.

10. Undo the bracket holding the centre-bearing of the prop-shaft by removing the 13mm nut either side.

11. Uncouple the prop-shaft from the gearbox by pulling the centre-bearing down enough for the locating pin on the gearbox to be clear of the prop-coupling. The front of the prop can now be lowered and moved to the side. If you have the whole car raised on a lift, then you will need to support the front of the prop, or remove the rear coupling to the diff. and get someone else to help you lift it down.

12. Remove the live terminal from the starter-motor using a 13mm wrench and the earth-terminal using a 10mm wrench.

13. Remove the 3 screws holding the starter-motor to the engine using an E10 double-hex socket and work the starter-motor out from the gearbox.

14. Disconnect the reverse-light switch by depressing the metal wire-clip to remove the plug and unclip the wire along the gearbox.

15. Clamp the rubber-hose to the clutch slave-cylinder and disconnect the clutch-line where the slim metal tube enters the slave-cylinder. This is done by prising the metal-clip out of the connector with a small flat-screwdriver and pulling the rubber-seal out of the slave-cylinder. Don't worry too much if you cannot clamp the clutch-hose, but it will involve more bleeding later on, which is a nightmare.

16. Remove the four bolts from the lower half of the gearbox bell-housing attaching it to the sump using an E10 double-hex socket.

17. Remove the remaining 6 large bolts from the gearbox bell-housing holding it to the engine-block using an E12 double-hex socket. [As in diagram.] The 2 down each side of the bell-housing are easy enough to access, but the 2 at the top are quite tricky. There is no easy way to get them, so it might be worth feeling around the top of the gearbox with the socket only until it is on the bolt and then get the ratchet / extension bar or CV-jointed socket to them.



** CAUTION: The gearbox will now be loose and held to the engine only with the locating-pegs, so ensure it is safely supported! **

18. Gently prise the gearbox away from the engine until it is clear of the locating-pegs and held up only by the centre-spline. Rocking it side-to-side should also help here. Draw the gearbox back slowly until the centre-spline is clear of the clutch/flywheel and the gearbox can be safely lowered partially. ONLY LOWER IT ABOUT HALF WAY!

19. Disconnect the wiring-connector from the cars neutral-sensor, located at the top of the gearbox by reaching around the top while it is partially lowered and pressing in the plastic clip on the connector. Fully lowering the gearbox before disconnecting will stretch the wire and potentially snap it!

20. Fully lower the gearbox safely onto the ground.

21. The clutch is now accessible, bolted to the back of the flywheel at the back of the engine. The clutch is removed by undoing the 6 bolts around its circumference using a 6mm allen-key socket [shown in photo]. The clutch can now be prised away from the engine! Be careful the clutch does not drop at this point, so it is best to support it with one hand while loosening the final bolt.

22. Remove the release-module / bearing from the spline inside the gearbox bell-housing. The metal lever should be held in place on the opposite side to the slave-cyinder by a piece of metal-wire and after removing that it should easily pull off. [If your clutch-kit includes a new release-module that is - if you are not replacing this then leave the old one in place.]

RELAX! You are now half way through the job!

23. Clip the new bearing into the new release-module as per the clutch-kit instructions and refit it to the spline in the gearbox bell-housing, replacing the wire-clip.

24. Fit the new clutch friction-plate into the new pressure-plate and mount it to the back of the engine leaving the 6mm allen-bolts loose by a few turns so the friction-plate can be moved around inside, but will hold in position.

25. Use the correct clutch alignment-tool to centralise the clutch, or if you do not have one look directly into the centre bore of the clutch and centralise the friction-plate by hand. It does not have to be perfectly in the centre, so you can get it accurate within about 0.5mm by eye.

26. Fully tighten the 6mm all-bolts.

27. Partially raise the gearbox to leave a few inches clearance above it and reconnect the wire to the neutral-sensor.

28. Fully raise the gearbox so it is in line with the back of the engine and move it forward, guiding the centre-spline into the clutch. Rocking the gearbox left-to-right should locate the spline into the clutch plate without too much fuss and it should then be able to rotate into position to meet the locating studs. The main problem here is the height and pitch of the gearbox on the jack / gearbox-stand, so watch out for differences in the gap at the top and bottom of the bell-housing when marrying it up.

29. Reverse steps 17 to 7. For tightening-torques refer to this post - http://www.beemerlab.org/2018/11/bmw-tightening-torques.html

30. Bleed the clutch - if you clamped the hose you shouldn't have too much trouble bleeding it, but the nipple is difficult to access and it can be easy to let air back in, so I have devoted a post to my bleeding issues here - F10: Clutch Bleeding Guide... the whole nightmare! [Manual transmission / gearbox 520d, 530d, F10, F11, G07, E90, E92 3er etc.]

31. Reverse steps 6 to 1.

F10: Clutch Pedal-Pin Repair / Replacement [E60, E90, E92, F01 etc.]

SYMPTOMS:

• Clutch pedal appears to collapse / become loose / twist to one side suddenly when depressed.
• Clutch pedal feels loose / collapsed and will not depress properly.
• Engine will not start and dash displays 'Depress Clutch to Start Engine' message while clutch is depressed.
• Gears will not engage or only partially engage while clutch pedal is depressed.

CAUSE:

Heavy clutch use / clutch-wear causes undue stress to the pedal-box [2 in diagram] and causes the plastic pedal-pin [8 in diagram] to snap / work its way loose. There are slim plastic clips at the end that stop the pin sliding out, but once these start to break off the constant motion makes the pin slide out very easily. When the pin is loose the clutch-pedal wont depress properly, which means the car cannot be put into gear or even press the clutch-switch to start the engine.

---

"GET YOU HOME" QUICK FIX:

1. Remove the trim-panel above the driver's footwell by undoing the T-20 Torx screws holding it in place. If you do not have tools to do this the trim can be forced off firmly and gently without breaking the plastic. The screw heads should pop out of the oblong holes in the panel, which can be bent back into place later and refitted.

2. Locate the end of the clutch pedal-pin where it has come out of the pedal-box, just to the right of the metal bar that attaches to the top end of the clutch-pedal.

3. Manoeuvre the clutch pedal back into position by hand, so the metal bar at the top of the clutch-pedal is straight with the eyelet either side of it in the pedal box and slide the pedal-pin to the left until it is fully into the far eyelet.

** This will get the car moving again to drive home, but the pedal-pin will soon slide back out. Reaching under the trim and locating the end of the pedal-pin will mean you can make sure it stays fully in place while stopped at traffic lights, so you technically run the car like this indefinitely. Still this is by no means a long-term solution. **

---

REPLACEMENT:

** You will need 'Clutch Pedal Pin' BMW Part no. 35306761029. **

1. Remove the trim panel above the driver's footwell that surrounds the pedals using a T-20 Torx socket.

2. Remove the coin-tray / stow-box to the right of the steering-wheel by undoing the two screws in the upper corners with a T-20 Torx socket and lifting it out top edge first.

3. Remove the single screw holding the electronics module to the right of the pedal-box using a T-25 Torx socket, remove the module from its housing and rest it somewhere out of the way.

4. Slide the pedal-pin to the right until it is out of the pedal-box.

5. Remove the push-circlip from the lower side of the clutch return-spring using a small flathead screwdriver [the one at the end of the stud that attaches the spring to the pedal itself], slide off the plastic spring-mount and fully remove both springs. [**DO NOT attempt to replace the plastic pedal-pin with the spring still in place as it will likely damage the plastic pin!**]

6. Grease the new pedal-pin.

7. Manoeuvre the clutch pedal back into position by hand, so the metal bar at the top of the clutch-pedal is straight with the eyelet either side of it in the pedal box and slide the new pedal-pin in from right to left until it is fully clipped into the far eyelet.

8. Hold the spring assembly in position against the upper spring-mount and compress it by hand until the lower mount can be pushed back over the stud on the pedal. Replace the circlip.

9. Reverse steps 1-3.

---

'DIY' PERMANENT FIX:
If you can't get hold of a new pedal-pin, or if the new one snaps too [which is likely to happen in the end as the pedal-box wears], then a long-term solution can be fettled with a long bolt.

CAUTION: The original pedal-pin is plastic and therefore designed to snap before the pedal-box does. Strengthening it with a metal bolt MAY cause further damage to the pedal-box over time, particularly if the eyelets are worn or the clutch-wear problem is not addressed.

1. Remove the plastic pedal-pin, as above.

2. Find a long M8 or M10 bolt and nyloc-nut. The bolt will need to be about 6 inches long. Any longer and it will foul things under the steering-column, but it needs to be long enough to reach through both sides of the pedal-box and get the nut on at least half a turn into the nylon. A 'shank' bolt [smooth down the shaft and only threaded at the end] is the best type to use. A flat washer on either side is also recommended, thin nylon washers being even better.

3. Take the plastic pedal-pin and drill the hole down the centre out: 8mm for M8 bolt, 10mm for M10.

4. Grease and re-insert the plastic pedal-pin to the pedal-box.

5. Grease the bolt and slide it in from the left side of the pedal-box, so the bolt is entering the far end of the pedal-pin, until the threaded end exits the right side of the pedal-pin.

6. Fit the nyloc-nut, ensuring the thread is into the nylon by at least a half-turn, as the constant pedal motion will work it loose otherwise. DO NOT over-tighten or put stress on the pedal-box!

Thread I started about this on Bimmer-Forums - http://www.bimmerforums.co.uk/forum/f15/2012-f10-530d-clutch-pedal-pin-snapped-twice-t494842/

E60: New Engine finally running!

Changed the injector seals last Sunday and gave the ports another good clean. The mist has stopped, but it still did not want to fire. There is fuel to the injectors and the timing is spot on, so this could only mean 2 things - something electronic isn't working properly, or the entire DDE module has fallen out of sync with the engine...

I don't even want to know what the latter option entails, so carried on swapping sensors on the new engine for those that worked on my old one. I found the crank-sensor was completely covered in dirty oil, in fact the whole slot was filled with it. Engine sensors are funny things and I can see how the oil could stop it from seeing the notch on the flywheel, but it doesn't explain why the engine would not turn over well using a can of Easy-Start. Either way, with the crank-sensor from my original lump in place it fired up straight away! Result.

[Video is with EGR-pipe disconnected and no air-filter / muffler fitted.]

• PAS-pump sounds like it's dying - extreme whine / groan when the wheel is turned - and is now the only thing keeping her off the road. Will try bleeding tomorrow and maybe fresh fluid, but failing that the pump could have packed in or, worse, I've damaged some of the piping / rack while lifting the engine in.
• Rear rubber exhaust-hanger missing. TIS says to remove the screws holding the hanger-bracket, not remove the rubber. I cut mine off to hastily get the exhaust down and will have to buy and annoyingly fit a new one.
• Front exhaust vibration-damper simply will not fit. When fitted to the exhaust, the eyelets on the two connecting-rods are way off the studs on the gearbox-bracket. The left-right rod is only about 5mm out, but the front-rear rod is miles off. I will have to remove the rear and centre brackets and try to relocate the exhaust a bit.

Other than that, no iDrive messages, no engine-management light, no 'Increased Emissions', no leaks, no mist and no funny noises. The gearbox and clutch are working fine and the car is desperate to be driven. Curse that power-steering fault!

E60: Engine Swap Week - Day 7

• Remove inlet-manifold, rail, injectors and rocker cover.
• Improve fit of fuel-rail return pipe.
• Clean injectors.
• Clean out injector ports in head.
• Fit original rocker-cover.
• Adjust injectors to fit collars tightly.
• Look for fuel in rail and rail-pressure when cranking.

The only thing I didn't do today was swap my crank-sensor over. I figured the automatic models have a different flywheel so would have a different sensor, but the two transmissions share the same sensor [exact same part no.] so the one that's on should work.

The banjo on the fuel-rail return hose needed refitting, as the jubilee-clip was now fouling the inlet-manifold. It was a bugger to find a way to refit it and give enough gap - the manifold is still fouling slightly.

I fitted my original rocker-cover because the new one has a crack round the MAF-sensor housing, obviously where the donor car had it's bump. The injector collars were fitting a bit loosely in the new rocker-cover too and are a bit tighter now. My original cam-sensor is back on too, which I doubt will make a difference, but can't hurt.

• Re-attempt start!

NO! The engine is turning ok and there is fuel-pressure. Sadly, there is now a lot of diesel-mist shooting up past the injectors, as in the vid below. Ah well, nothing ever goes smoothly.

E60: Engine Swap Week - Day 6

• Replace snapped T-piece on injector leak-off pipes.
• Torque up crank-pulley and HP-pump.
• Refit drive-belts.
• Refit radiators / coolers.
• Refit headlights and crash bar.
• Refit slam-panel and grilles / ducts.
• Plumb cooling, A/C and PAS back in at the front.
• Loosely refit exhaust and heat-shield.
• Fill with oil and coolant.
• Refit ECU and plug loom in.
• Plug in all wire connectors to engine.
• Refit fuel-rail and pipes.
• Refit turbo and exhaust-manifold.
• Refit rocker-cover and injectors.
• Refit inlet-manifold.
• Attempt start!

NOTE: Fasten engine-mount top nuts! Neaten up fuel-rail return pipe!

Well, sadly, it didn't fire right up in the first few tried like last time, but the battery has been sitting for a month and died quickly, so I will charge it overnight and have another crack tomorrow.

• Check for missing wire-connectors. Crank-sensor?
• Bleed injectors and check for rail pressure.
• Flywheel position sensor - is it a different flywheel? Swap to original.
• Check injector-leads for pulses with multimeter.
• High-pressure pump - does it need bleeding? Is it working?
• Is 'Service Due' warning affecting immobiliser?

If all these check out and it still won't go then I will have to get a computer on it and get some fault-codes. I'm back in work next week, without a break, so I should be able to bring the Launch home.

It's been a hella lot of work the last 6 days so it would have been nice to have the engine fire up on the third go like it did when I fitted the new cylinder head, but ah well, I'm full of optimism at the close of today.

Plastic T-piece nozzle snapped off in the injector leak-off hose. Luckily I got fuel pipes with the new engine [even though the pump itself was missing] and didn't have to buy a new one.

From an '03, to an '09 and now back to an '04 - this is the third head in the E60.

E60: Engine Swap Week - Day 5

• Attempt to lift gearbox underneath car.
• Lift engine back out.
• Fit gearbox to engine.
• Remove bonnet / A/C-duct.
• Lift engine and gearbox in together [mm to spare!].
• Fit prop-shaft.
• Fit gearbox mounts.
• Fit starter-motor.
• Fit oil filter/cooler.
• Fit alternator.
• Fit PAS-pump.
• Fit A/C compressor.
• Fit thermostat.
• Re-attach lower wiring-connectors.

• Loosely fit crank-pulley.
• Loosely attach main electric-cables to alt / starter.
• Loosely fit anti roll-bar.

NOTE: remember sump wire connector + tighten 10mm screw on gearbox!

Gearbox was getting nowhere from below with so little room under the car, so the engine came back out and we lifted the gearbox on very easily.

By removing the plastic air-con duct at the back and popping the bonnet lifters off so it lifts up vertical, it is possible to just about lift the engine and gearbox in together without lowering the subframe / rack.

Just the rads and injectors now and it's pretty much ready to start.

E60: Engine Swap Week - Day 4

Had a lost day yesterday when the engine didn't arrive. It only turned up at 1.30pm today, so I will have to concentrate on swapping over the high-pressure pump, flywheel and clutch, as well as removing the loom etc. ready to patch mine in. Lifting the engine in will have to wait until tomorrow.

• Replace steering-rack / subframe bolts entirely.
• Remove loom and vacuum-hoses from new engine.
• Swap over high-pressure fuel-pump.
• Fit flywheel and clutch.
• Remove oil filter/cooler and rocker-cover for lifting.
• Match engines entirely.
• Lift engine in.

Engine arrived at 1.30pm.

And was finally sat in the bay at 7.30pm.

E60: Engine Swap Week - Day 3

• Drop prop-shaft.
• Remove slave-cyl. / gearshift linkages.
• Drop gearbox.
• Lift engine out.
• Remove parts for new engine.

Once the prop was down it didn't take long at all to get the engine out. The gearbox is huge, but surprisingly light.

Prep for new engine:

• Remove clutch.
• Remove flywheel.

Got the clutch off easy enough, but need a T55 Torx socket to remove the flywheel so that will have to wait until I get it from work tomorrow.

NOTE: Missing bolt from exhaust cross-member.

E60: Engine Swap Week - Day 2

• Remove headlights and front crash-bar.
• Remove starter motor.
• Remove oil filter / cooler.
• Photograph and disconnect vacuum hoses and wiring-connectors.
• Attempt remove engine.
• Remove exhaust-system.
• Remove heat-shield.
• Remove gearbox mounts.
• Remove 2 of 3 prop-shaft bolts [coupling to gearbox].

Sadly, the first attempt did not work. The sump still gets stuck on the sub-frame. TIS says to first remove the prop and gearbox, so it looks like this is the only way.

POA for Day 3:

1. Bolt gearbox mount back up.

2. Loosen remaining prop-shaft bolt.

3. Lift car and put axle-stand under jacking point.

4. Support gearbox and remove mounts.

5. Drop prop-shaft.

NOTE: Cut off rubber exhaust-hanger needs new - Part no. 18207578238

Blue nylon rope not the best for lifting engines, but note a lot of weight is removed from the engine - head, ATF-pump, oil filter-cooler, A/C comp etc.