E46 318i Touring: Replacing leaky Oil Cooler gasket [N42]

After fixing the major oil leak from the rocker-cover gasket [THIS POST], I noticed there was still some oil pooling on the under-tray and a fews spots dripping onto the road. I traced the source up the right side of the engine (looking from the front) and could see oil filling up some cavities in the cylinder-head to the left of the oil-cooler / filter housing, so determined this to be the culprit... yes, another common one, especially if the filter-housing has been removed for previous engine work.

A replacement gasket was just £6.59 from eBay and comes as a two piece set including the main gasket that sits between the housing and the cylinder-head, as well as a smaller gasket that sits between the oil-filter housing and the coolant fed heat-exchanger. This latter one hardly ever leaks, as it's very rare to find a filter-housing that has been split apart during engine work, but it's nice to have one anyway and you may find it worth the time to replace this one while the housing is removed, though I could not see any signs of leakage so didn't bother.

GUIDE:

1. Remove the lid to the air-con ducting that sits atop the firewall at the back of the engine by undoing the clips a quarter-turn, take out the pollen-filter and remove the weather-strip seal from the firewall.

2. Remove the air-con ducting itself by undoing the four screws using a T30-Torx socket and lifting it out.

3. Remove the rear right-side engine cover by undoing the two stud-nuts using a 10mm wrench.\

** Make sure you have a cloth / plenty of tissue to catch any oil that runs from the housing. **

4. Remove the three screws holding the oil-filter / cooler housing to the cylinder-head using a 10mm socket with a long extension bar. One is clearly visible in front of the housing, the other two being hidden down the back.

5. Lift the oil-filter / cooler housing upwards out of the head, catching any wayward oil and lift the housing clear, rotating it so as not to put too much strain on the coolant-hoses. The hoses do not need removing or any coolant draining for this job.

6. Remove the old gasket and clean both mating surfaces with a cloth and I find it always worth scraping any crud off with a razor-blade.

7. Insert the new gasket to the housing. A lug on one side sits in a notch in the housing so the gasket can only fit in one way. [If it's an older engine or the housing has been removed a few times before, it might be worth taking a belts-and-braces approach by applying some gasket sealant to the mating surface on the head, as I did with some white Corteco.]

8. Carefully place the filter/cooler housing back onto the cylinder-head, trying to spill as little oil as possible on the mating surface and reverse steps 4-1 to refit.

UPDATE: F10 off road with DPF issues... E46 Touring joins the stable!

So, quite an eventful couple of months... first I rectified the hi-beam headlight issues on the F10, only for it to then fail the MOT on emissions due to a blocked DPF and new regulations. Work on my house meant that I had no time to sort it and needed a car, so ended up buying an E46 318i Touring for the princely sum of £400. It's got 102k miles, MOT until October and is purple... enough said.

---

F10 DPF / Emissions woes...

New UK emissions rules [info here] for diesel cars are extremely choking [excuse the pun]. The law states that diesel cars made after 2008 must no longer adhere to a generic CO2 value, previously 3.0 m-1, but instead must produce emissions lower than the manufacturers plate value... in BMWs case this is 0.5 m-1. Therefore, to pass a UK MOT test on emissions the car must now produce 1/6th of what used to be considered acceptable! There is still a generic value to test to, only halved at 1.5 m-1 and easier to pass, but this only applies when there is no 'manufacturer plate-value' and sadly the F10 has one.
To make matters worse, any emission of black smoke from the exhaust pipe on a post-2008 vehicle fitted with a DPF is an instant fail!

My first emissions test produced just shy of 1.8 m-1. In past years this has been well within the acceptable limits, my Dad's 2004 Audi A4 diesel producing nearly 2.8 m-1 and passing for instance, but since April 2018 the limit is 0.5 and my 1.8 is well over. I ran a bottle of CataClean through and gave the car a good 20 mile run up and down the motorway, then returned to the test-station for another go. This time I rolled just under 1.5 m-1 of CO2, an improvement but still well above the permitted 0.5. Besides, it was pointed out to me that the car was emitting a puff or two of black smoke during the tests, so it didn't really matter and this only pointed to one thing... a blocked DPF.

After trying a re-gen through software, I realised that the DPF would need to come off the car to be cleaned out / replaced before this was going to happen. A new DPF from BMW is £1596 +VAT... so lets not even go there. Used or reconditioned DPFs.. hmm, I decided to give those a pass too, along with cheap spurious models that I've heard nothing but bad things about. No, instead I will have to clean out the heavily clogged one I have now, so watch this space as I will post results soon.

Yeah, a lot going on and you can see why I needed a cheap runaround!

BMW F10/F11: Clogged/blocked Washer Pump Filter - EASY FIX / FILTER REMOVAL! [E90/E92/F07/F30 etc.]

Windscreen washer jets not working, but the pump can still be heard OK? Then you have a very common case of clogged filter. Due to the supposed inaccessibility of the bottle on later model BMWs I have read stories of high dealer bills, daunting inner-wing removal and even back-feeding the washer-hose with bleach to gradually unblock the gunged up filter... but before you try this read on, as it is an easy fix after all.

GUIDE:

1. Fully turn the steering to the right to give access behind the driver's front wheel to work. [Removing the wheel will give more access but is not necessary.]

2. Remove the 6 screws holding securing the rear half of the felt wheel-arch liner in place using an 8mm socket. This will allow access without removing the arch-liner completely. Four of the screws are located in the wheel well itself and two are located underneath next to the sill.

3. Remove the plastic 'mud-guard' trim on the outside of the wheel-arch that adjoins the felt arch-liner. This is done by pressing the centre-pin of the 3 plastic clips through the clip and then removing the clips with a panel-popper tool. [It may be possible to do the job without removing this trim piece, as the clips are very hard to get out and prone to breaking, but visibility and access are certainly improved].

4. Peel the felt wheel-arch liner out from the rear lip of the wheel-arch and if possible tuck it behind the wheel. The washer-bottle should now be visible to the rear of the front wheel. It sits in a tight gap between the outer and inner wings of the car body itself and access is very limited. [This is unlike E39, E60 etc. where the bottle sits left-to-right across the rear of the wheel-arch and access if much easier!]

5. Remove the windscreen washer hose from where it enters the pump and move it out of the way.

6. Slide a long flat-screwdriver in between the washer-bottle and the outer wing and prize the pump upwards until the spout is clear of the bottle and the pump can wedged up and out of the way.

7. The clogged filter should now be sitting in the washer-bottle where the spout of the pump fits. Use the flat-screwdriver to prize the filter up and out of the bottle. It should now be removable by hand or using long-nose pliers / tweezers.

8. Clean the gauze filter using water and lightly brush it with a sponge-scourer or stiff brush. [I find an old toothbrush works perfectly.] It is likely clogged with a 'gel' like substance that builds up supposedly due to the use of incorrect washer-fluid as well as dirt from the bottom of the tank if the washer has been run without fluid in for a while, but should clean up pretty easily.

9. Carefully slot the filter back into the washer-bottle and press it back into place using long-nose pliers / flat screwdriver or both, making sure it is fully seated.

10. Slide the pump spout back into the filter / washer-bottle, making sure it is fully seated and rotated to the correct position with the spout for the windscreen-hose pointing to the side of the car.

11. Refit the washer-hose, trim, wheel-arch liner and wheel. [Reverse steps 1-5.]


www.e90post.com/forums/showthread.php?t=930107
http://www.bimmerfest.com/forums/showthread.php?t=737416
http://forum.bmw5.co.uk/topic/120732-f10-windscreen-washer-not-working/
http://forum.bmw5.co.uk/topic/124943-f10-washer-problems/

E36 Compact: M43 Oil Change + Filter Removal.

Got round to changing the oil and filter on the Compact, as I've been running it for a month with the mayonnaise filled concoction left from the dodgy head-gasket / cooling issue.

Removing Oil-Filter:

The filter-housing on the later M43 316i / 318i is right down in the bowels of the engine and impossible to get to easily, as they are on almost all other BMWs. The lid has no nut either to undo it from above, so the only way is to use an old-skool oil-filter removal tool from the side, only most of the engine prevents this.

The simplest way to get it off is to remove the fan-cowl and fan. This way there is just about enough room at the front of the engine to get a turn on the filter with the removal tool. I found a chain based removal tool works well, but a steel-belt one would probably be just as good. It isn't essential, but I removed the top inlet-manifold too, just to see what I was doing more clearly.

1. Remove the fan-cowl by undoing the two top screws with a 10mm socket and lifting it off, popping it out from the air-inlet ducts at either side.

2. Remove the two 8mm screws holding either side of the rear edge of the fan-housing at the top and lift the fan vertically up, sliding it out of the two bottom lugs.

3. Slide the removal-tool in from the front and there should now be room enough to get a turn on the filter-housing lid, even if it's as tight on as mine was.

E46: New secondary air-pump - one last bash...

Thought I would have one ultimate stab at the E46 as it is such a nice car to drive and only let down by shabby bodywork, which I can do something about, and the super low idling problem, which apparently I can't.

I refitted the Vanos-actuator and checked for anything I'd disturbed under the inlet manifold, finding a loose wire connector which I clicked back in, though the CCV was all plumbed up fine. A replacement secondary air-pump and its hose / filter was £30 and the only thing now missing from the inlet arrangement. It took no time to fit, just two 13mm bolts holding it on and swapping the hoses over, but has still, alas, made no difference.

I've spent nearly £300 on parts to cure this engine of its fault, but nothing has done the trick so I guess I will have to call it a day and scrap her after all. Again a shame, as it has 9 months MOT and 4 months tax left on it. The running gear is sound, I sorted the brakes and the engine runs fine when underway, pulling well in all gears over 1500rpm. Handling is as sweet as any E46. The interior and exterior are in terrible nick, but thats nothing that couldn't be sorted with a day or two spent on it. That's only worth doing if the car is useable however, and it sadly isn't.

On top of the impossible low-idling, the handbrake-shoes have collapsed in some way and stick on completely in reverse with the handbrake off. This is probably from being used so much to stop the car while my right foot was still keeping the revs up, but is extra work regardless. A large M12 bolt holding one of the front shock-absorber struts broke while I was attempting to fit the coilovers months ago. I've been driving on it and the strut hasn't moved at all, but it too will need replacing at some point and removing the stud will be interesting. Inside the car, the fan for the heater/blower doesn't work and the driver's door card is missing, meaning no speaker or door handle. Exiting the car with dignity can only be done by lowering the window and reaching out for the other handle, but all these foibles I rather liked. Using it every day was a nightmare though and, with the 5-Series engine swap underway I just won't have the time and money to restore it, so I'm hoping I can get the £200 I paid for it back from a breaker. That means I'm down about £300 on the whole deal. I could make the £500 back and probably more by breaking the car, but I could really do with it out of the way quickly now so a loss it may have to be.

E21 316: Engine-Bay Painting 1.

Brake servo and 'Puralator' air-filter were in need a revamp, thought I'd do the scuttle-panel cover as well.

Quick rub-down, blast of zinc-primer and then a good coat of BMW Black spray.

The engine looks a bit more cared for now!

E39: Replacing / Unclogging the Washer-Jet Pump

If you think your pump is faulty then check this post first - Windscreen Washer-Jet System Problem.

-----------------------------------------

Removing the pump is easy, but getting to it is quite involved due to the amount of under-car panelling the E39 has.

PROCESS:

1. Jack up the o/s front of the car and detach the plastic mud-guard by removing the 3 hex-head screws that hold it to the wheel-arch. using a 7mm wrench.

2. Lift off the plastic under-tray that sits to the rear of the wheel-arch by removing the 5 plastic-studs around its edge. If you lack a took for pulling out this kind of stud then lever the head of the centre-pin out a few mm with a flathead screwdriver and then slide it clear with pliers. The body of the stud should now slide out easily.

* The car may need lowering to remove the under-tray and re-lifting, as the jacking-point lies in the centre of it.

3. Remove the 7 hex-head screws around the inside of the wheel-arch. as well as two at the leading edge of the under-tray, unseat the inner wheel-arch from around the lip of the wheel-arch itself and pull the plastic inner-arch down out of the way.

* The water-tank for the windscreen and headlight washer-system is located just behind the wheel-arch, below the front of the driver's door. Not the Intensive cleaning-system, which has both the tank and pump under the bonnet.

4. Unplug the wire-connector from the pump in centre of the tank**, by sliding a flat screwdriver into the clip and lifting it upwards.

5. Pull the slim hose-connector clear of the central pump** and allow the tank to drain.

This is a good point to test the washer system one last time to make sure it isn't a blocked hose and the pump is getting no water.

6. Gently twist and pull the pump upwards about an inch out of its mount, then remove the black rubber-bush it sits in.

7. Flush the tank several times by pouring water into the filler-nozzle under the bonnet and allowing it to drain through and clean around the lip of the pump-mount. Check the pump for clogging.

8. Replace the rubber-bush to the tank and, using the new pump if necessary, reverse the procedure.

** The pump in the centre of the tank with the slim hose is for the windscreen washers. The left-hand pump with the larger hose is for the headlight washers.

*** The black connector on the inner corner of the tank is the level-indicator probe. This is also a push fit and the best place to drain from, after removing the wire-connector as above.