F10: Rear Shock Absorber / Strut / Spring Replacement [GUIDE]

*Front strut-assembly replacement guide here - https://www.beemerlab.org/2017/09/f10-530d-front-shock-strut-spring-top.html*

Time to do the rear struts and springs on the 530d F10 this week as one damper has been leaking and while doing my tyres last week I noticed the spring has now broken at the bottom so this is now an urgent job. I picked up a pair of used complete struts (spring, damper and top-mount) from eBay for just £100. They are from another 530d and claim to be from a low mileage car. Well, they look a lot lower mileage than the ones I'm taking off lets put it that way and appear to be in pretty good condition. I get a lot of stick for constantly using second-hand genuine parts, but I still prefer this to buying new spurious parts where I can and have never had an issue!

GUIDE:

* This is not a difficult or time-consuming job, but will require a bit of brute force. *

1. First the rear seats need to come out. Lift the seat squab up at the front and detach it from the push-studs, press the seat-belt receivers through the recesses and lift the squab out. Next lift the seat-back upwards until it is free of the hooks at the top and lift that out, being careful of the door-sill paintwork and sliding it through the seat-belts. [You could always unbolt the seat-belts at the base using a T45-Torx socket to make this easier, but it's not essential].

2. The parcel-shelf now needs to come down in order to access the strut-top mount bolts in the shock-turrets. Remove the C-pillar trims by prizing out the plastic caps labelled 'Airbag' from the trim and removing the screw using a T25-Torx socket. Now carefully pull away the C-pillar trims and put to one side. Remove the five push-pin clips from the front edge of the parcel-shelf by levering the button in the centre upwards and pulling the plastic pin out. The studs can now be levered out. The parcel-shelf is now free to pull forwards and can be rested where the seat-back would be. [Remove the wiring-connectors to the speakers, but these should pop out by themselves anyway].

3. Lift the car and remove the corresponding wheel. [There is no need to be getting under the car for this job, so a jack and axle-stand is fine].

4a. The track-strut (pictured) needs to be moved out of the way to access the bottom strut bolt so first remove the plastic clips holding the E-brake wire-harness to the track-strut by levering them open at the bottom with a flathead-screwdriver and separating them from the strut. The wire-harness can be moved out of the way.

4b. Remove the bolt holding the inner end of the track-strut using an 18mm wrench. Pull the track-strut down and rotate it so it is pointing out of the wheel-arch. You now have plenty of room to get at the bottom strut bolt and lift the shock out.

5. Remove the bolt holding the bottom of the strut to the hub using a 21mm wrench.

6. Lift the triangle flap in the foam underneath where the parcel-shelf was to expose the studs to the strut-top mount and remove the three nuts using a 13mm wrench.

7. Wiggle the bottom of the strut free from the hub and the entire strut assembly is now free to be removed. It should be able to be lowered through the remaining suspension parts and to the rear of the car until it is free to be removed.

** IF YOU ARE CHANGING THE SPRING / TOP-MOUNT OR SWAPPING THESE ONTO A NEW STRUT THEN DO THIS NOW** [See this post for guide].

8. Make sure the new strut has the top-mount in line with the old one you removed by lying them next to each other and checking the bottom bolt-eyelet and triangle marking on the top-mount match up. [The triangle marking on the top-mount should face towards the back of the car with the bolt-eyelet facing the centre, or with the triangle marking facing you the bolt-eyelet should be pointing to the right for O/S (right-side) and left for N/S (left-side)].

9. Lift the new strut back up through the suspension and line it up into the strut-turret. [Triangle marking on top-mount facing rear of car] and screw the three 13mm nuts back on a few threads.

10. Lever the hub downwards until it meets the bolt-eyelet at the bottom of the strut meets its recess on the hub and screw the 21mm bolt back in about half-way.

11. Fully tighten the three 13mm nuts on the strut-top mount.

12. Fully tighten the 21mm bolt through the bottom of the strut.

13. Replace the track-strut / wheel as a reversal of steps 3 and 4.

14. If you are doing both sides then repeat steps 3 - 13 for the opposite side.

15. Replace the parcel-shelf, trim and rear seat as a reversal of steps 1 and 2.

F10 530d: Front Shock Strut / Spring / Top-mount Replacement [GUIDE]

*Rear Strut-assembly Replacement Guide here - https://www.beemerlab.org/2020/12/f10-rear-shock-absorber-strut-spring.html*

My front shocks were certainly past their prime up front and over the last few months have really started to bottom out on certain speed bumps. I was also told one of the front top-mounts was starting to go on the last MOT and would probably be an issue next time round, so it was time to give the F10 a mini front-suspension overhaul.

I got hold of a pair of complete front struts taken from a 45k-mile car (I am told, but they are very clean) for just £240. All the parts new and spurious (including my through-work discount) would have been nigh on £400 and lots more from BMW. The used items are of course genuine, so quite a lot of money saved and the struts have turned out to be pretty good so it was a chance worth taking.


The guide I used is by hamanncheese on 5post.com and is pretty spot on, so props to him - I will reference his photos and try to elaborate a little on his instructions. [Original guide here: http://f10.5post.com/forums/showthread.php?t=628336].


REMOVE / REPLACE STRUT:

1. Lift the car and remove the corresponding wheel.

2. Remove the nut holding the top of the anti-roll bar link to the shock-strut using an 18mm wrench. [The nut should come off without twisting the ball-joint, but you may need to insert a T40-Torx socket into the end of the stop it turning with the nut.] [If the stud is difficult to remove from the shock-strut, then using a second jack to lift the hub and prying the anti-roll bar downwards will certainly help.]

Pic courtesy: hamanncheese

3. Remove the lower strut bolt using an 18mm (bolt-head) and 21mm (nut) wrench.

Pic courtesy: hamanncheese

4. Remove the 3 bolts holding the top-mount to the shock-turret using a 13mm wrench.

Pic courtesy: hamanncheese

5. Push the hub down and lift the shock-strut until it clears the bottom-arm and can be removed. [Lift it over the bottom-arm towards the rear of the car. There is plenty of room to manoeuvre it out of the wheel well.] [As hamanncheese says, this step is easier with a helping hand, but can be done solo without much difficulty.]

6. Insert the new strut using the same technique as Step 5.

7. Refit the lower strut bolt first and screw the nut on a few turns. [A screwdriver or other long tool may be necessary to align the strut to the lower-arm.]

8. Refit the 3 top-mount bolts and tighten.

9. Fully tighten the lower strut-bolt.

10. Refit the anti-roll bar link to the strut.


ALIGN TOP MOUNTS:

If the top-mount holes do not line up with the shock-turret, [i.e. if they have been removed / replaced and not fitted in the correct alignment], then they will need rotating to the correct position. Spring-compressors are required.

1. Place the strut on its side with the ring-bracket resting on the floor [as in pic]. This is so it can be lined up against the one it is replacing.

2. Compress the spring on both sides, being careful to mount the spring-compressors so they do not foul the strut resting on the ring-bracket [as in below pic].

3. Loosen off the top mount nut using a deep 18mm socket, leaving it on a few threads.

4. Rotate the lower spring-pan by tapping it round using the notches [in pic]. A hammer and blunt chisel or large flat-head screwdriver will do nicely.

5. Re-tighten the top mount nut and de-compress the spring.


REPLACE SPRING / TOP-MOUNT:

1. Compress the spring on both sides using spring-compressors.

2. Remove the top-mount nut using a deep 18mm socket. [Stand to the side when the nut is fully removed as, even with the springs compressed, the top-mount may still come off with some force.]

*If you are only replacing the top-mount then skip Step 3.*

3. If you are replacing the spring, remove the old one from the strut and remove the spring compressors. Compress the new spring, place it over the strut and seat it in the lower spring-pan.

4. Fit the new top-mount, ensuring the spring is located in the upper spring-pan, replace the 18mm top-nut and fully tighten.

5. Remove the spring-compressors.

F10 530d: Black leather rear-seats and door cards WIN - front-seats FAIL!

Lovely front seats do not fit.

Thought I would treat the F10 to a nice leather interior, replacing the tired and fluffy cloth front seats and scratched / dirty door cards, after spotting a complete set from a 2014 car on eBay. I managed to get £100 knocked off the price and drove down to Stourbridge to grab them with a distinct feeling that it was too good to be true. I had to climb nearly 20 feet up a ladder to retrieve them, but they were seriously mint - honestly, not even a mark on any bit of leather - so I parted with the measly £300 and brought them home.

My gut feeling turned out to be right. While the rear seats and door-cards are a perfect fit, the front seats are not. From mid-2013 onwards the F10 floor-pan was updated, along with the mounting-points for the front seats and this means that the runners on my new seats are a couple of inches narrower than on my original 2010-13 seats, which are clearly wider at the base. There is no way to swap the runners, the seats are just too different in design and I will write a more detailed guide on this soon. Annoyingly, the electric plug fits and the motors operate, though they throw up too airbag warnings.

Door cards are straight swap.

Modifying the seats or floorpan to fit is just too much work and will not look very nice, so the only way to go is wait until a pair of front seats for a 2010-13 car come up and try to part-ex mine or at least sell them later. Either way, this could end up costing me more. Regular SE seats are quite thin on the ground for the earlier cars and M-Sports are upwards of £400.

Rear seats fit great.

** Correct seats now acquired here: https://beemerlab.blogspot.com/2016/08/f10-530d-correct-front-seats-acquired.html **

E60: Split Vac-line, some boost, weird noises.

The turbo whine and lack of boost has persisted, so I took off the inlet-manifold again to check the vacuum-lines and found one has snapped off. Luckily, there was plenty of hose left to cut it down and push it back onto the T-piece. I re-checked every line twice against the diagrams on RealOEM.com and refitted the manifold, making sure the seals were super flush. Now when I fired up the turbo started making a ridiculous whoosh and dump-valve style hiss, as in the vid below. Some boost had returned too, though not as much as there should be and certainly nothing like the turbo sounded. Still, the vac-line repair did get a result, so it looks there could be life in the turbo yet.

There was nothing else I could do other than pore over the vac-line configuration, so I made this quick one-piece diagram to show the route of the four coming off the servo-pipe to save switching between several diagrams on RealOEM. I then started pulling vac-lines off in order to find the faulty area and, amazingly, managed to get rid of the whoosh/hiss and still have some boost. The turbo is still whistling though and there is not enough pull as you get over 2k rpm, so something is still amiss.

• Split vac-line to swirl-flaps - Low boost, quiet turbo-whistle higher up.
• Repaired vac-line - Some boost low down, cuts out higher up. Loud whoosh and hiss noise, turbo-whistle constantly.
• Vac-hose removed from wastegate - Low boost, quiet turbo-whistle higher up.
• Swirl-flaps and engine-mount vac-lines switched round - Some boost, no whoosh/hiss, constant turbo whistle, less engine vibration.

The diagrams do not make clear the route of the red/black striped hose on the right of mine. This turned out to be the N/S engine-mount and another scan of RealOEM.com revealed how they work in the pic below. I had wondered about a problem with the engine-mounts anyway, as there seems to be a lot more engine vibration than before, especially on tickover, so my next job will be to find the pipes that link the mounts together and check their condition. They all run through the subframe next to the steering-rack. M57N is a complicated vacuum arrangement.

E60: PAS-Pump + Exhaust Vibration-Damper.

With everything else apparently working, the 530d was still of the road due to the niggling problem of an un-bleedable PAS-system and rattling exhaust.

• Bleed PAS-system with cap off reservoir and engine off, by turning the wheel lock to lock about 30 times and adding fluid until no more bubbles were coming out.
• Remove front-bumper and drive back onto ramps.
• Locate exhaust onto connecting-rods of vibration-damper.
• Modify connecting-rods to fit new exhaust position.
• Refit exhaust and reinforcement-plate.
• Refit engine centre-undertray.
• Drive off ramps, refit bumper and test drive!

PAS-Pump Bleed:

This is the hardest to bleed PAS-system I have ever come across, though the pipes / pump have been off the car for 3 weeks and could have allowed the system to drain and fill with air more than before. The pump was whining on tickover and making an almighty groan when turned in either direction. The fluid in the reservoir was also frothy white. To fully bleed it required the engine and reservoir cap to be off and the wheel turned full lock left to right about 30 times. To do this I raised the front of the car on axle-stands so the wheels were still touching, but with hardly any weight on them. The first turns lock to lock gulped the remaining fluid right into the system and so much air was coming out I kept re-checking the pipes for a leak. Eventually, the reservoir had swallowed the last of my bottle of fluid and is just about sitting up to the minimum mark, but still bubbles were popping up as the wheel was turned. The lock to lock business continued with me and my dad taking turns for quite some time until there were finally hardly any tiny bubbles rising to the surface. This whole thing was a job in itself, but the pump is very quiet now and the steering assistance is back.

Exhaust Vibration-Damper:
During the first tests there was an almighty rattle from the exhaust from tickover up to about 2k rpm. I assumed this to be because I had left off the exhaust 'vibration-dampers' that brace the bottom of the cat to the gearbox and stop it shaking. I discarded replacing it at first as, if you don't remember exactly the way it all fits together and start bolting your gearbox and exhaust back on willy nilly, then it's impossible to figure out. The long bracket with 3 holes fits around the edge of the gearbox bell-housing, held in by one of the large E14 and two of the smaller E10 Torx-bolts that hold the box to the engine. The connecting-rods then run from the foremost stud on the cat to the N/S stud on the bracket; and from the rearmost stud on the cat to the O/S stud on the bracket, as shown in the picture from TIS. Only trouble was, neither of the rods went anywhere near the brackets. I'm not sure if the entire engine and gearbox is in a slightly different position from before, or it's just the exhaust out of line, or both, but the eyelets on the left-right rod were about 5mm too long for the studs; and the front-rear ones were almost an inch too short. After 2 frustrating hours spent removing mounts and trying to relocate the gearbox / bracket to meet the exhaust I gave up and decided to modify the connecting-rods to fit the new gap lengths. The only remaining way to adjust exhaust position would be to loosen the two nuts holding the cat to the back of the turbo, only to do this requires the rocker-cover / injectors to come back off and I'm not doing that, for now at least.
The modified connecting-rods are below and, due to lack of time, are rather crudely done. I bent the left-right rod down about 3/4" at a steep angle to take 5mm length out of it and help bring it down to the bracket at a flush angle and works rather well. The front-rear was a bit less neatly done and makes use of a piece of 1mm sheet-steel, cut roughly to an inch square and bolted to the rod. It's not the best workaround in the world, but it gets the job done.
After all that, the 'vibration-damper' did not get rid of the rattle! Instead, I traced the annoying noise to the front rubber-mount a bit further down the pipe. The exhaust was banging right into the side of the metal bracket on the gearbox-mount and a bit of fiddling with the adjustable eyelet managed to separate them and killed the rattle dead, so there you go.

E60: Engine Swap Week - Day 7

• Remove inlet-manifold, rail, injectors and rocker cover.
• Improve fit of fuel-rail return pipe.
• Clean injectors.
• Clean out injector ports in head.
• Fit original rocker-cover.
• Adjust injectors to fit collars tightly.
• Look for fuel in rail and rail-pressure when cranking.

The only thing I didn't do today was swap my crank-sensor over. I figured the automatic models have a different flywheel so would have a different sensor, but the two transmissions share the same sensor [exact same part no.] so the one that's on should work.

The banjo on the fuel-rail return hose needed refitting, as the jubilee-clip was now fouling the inlet-manifold. It was a bugger to find a way to refit it and give enough gap - the manifold is still fouling slightly.

I fitted my original rocker-cover because the new one has a crack round the MAF-sensor housing, obviously where the donor car had it's bump. The injector collars were fitting a bit loosely in the new rocker-cover too and are a bit tighter now. My original cam-sensor is back on too, which I doubt will make a difference, but can't hurt.

• Re-attempt start!

NO! The engine is turning ok and there is fuel-pressure. Sadly, there is now a lot of diesel-mist shooting up past the injectors, as in the vid below. Ah well, nothing ever goes smoothly.

E60: Engine Swap Week - Day 6

• Replace snapped T-piece on injector leak-off pipes.
• Torque up crank-pulley and HP-pump.
• Refit drive-belts.
• Refit radiators / coolers.
• Refit headlights and crash bar.
• Refit slam-panel and grilles / ducts.
• Plumb cooling, A/C and PAS back in at the front.
• Loosely refit exhaust and heat-shield.
• Fill with oil and coolant.
• Refit ECU and plug loom in.
• Plug in all wire connectors to engine.
• Refit fuel-rail and pipes.
• Refit turbo and exhaust-manifold.
• Refit rocker-cover and injectors.
• Refit inlet-manifold.
• Attempt start!

NOTE: Fasten engine-mount top nuts! Neaten up fuel-rail return pipe!

Well, sadly, it didn't fire right up in the first few tried like last time, but the battery has been sitting for a month and died quickly, so I will charge it overnight and have another crack tomorrow.

• Check for missing wire-connectors. Crank-sensor?
• Bleed injectors and check for rail pressure.
• Flywheel position sensor - is it a different flywheel? Swap to original.
• Check injector-leads for pulses with multimeter.
• High-pressure pump - does it need bleeding? Is it working?
• Is 'Service Due' warning affecting immobiliser?

If all these check out and it still won't go then I will have to get a computer on it and get some fault-codes. I'm back in work next week, without a break, so I should be able to bring the Launch home.

It's been a hella lot of work the last 6 days so it would have been nice to have the engine fire up on the third go like it did when I fitted the new cylinder head, but ah well, I'm full of optimism at the close of today.

Plastic T-piece nozzle snapped off in the injector leak-off hose. Luckily I got fuel pipes with the new engine [even though the pump itself was missing] and didn't have to buy a new one.

From an '03, to an '09 and now back to an '04 - this is the third head in the E60.

E60: Engine Swap Week - Day 5

• Attempt to lift gearbox underneath car.
• Lift engine back out.
• Fit gearbox to engine.
• Remove bonnet / A/C-duct.
• Lift engine and gearbox in together [mm to spare!].
• Fit prop-shaft.
• Fit gearbox mounts.
• Fit starter-motor.
• Fit oil filter/cooler.
• Fit alternator.
• Fit PAS-pump.
• Fit A/C compressor.
• Fit thermostat.
• Re-attach lower wiring-connectors.

• Loosely fit crank-pulley.
• Loosely attach main electric-cables to alt / starter.
• Loosely fit anti roll-bar.

NOTE: remember sump wire connector + tighten 10mm screw on gearbox!

Gearbox was getting nowhere from below with so little room under the car, so the engine came back out and we lifted the gearbox on very easily.

By removing the plastic air-con duct at the back and popping the bonnet lifters off so it lifts up vertical, it is possible to just about lift the engine and gearbox in together without lowering the subframe / rack.

Just the rads and injectors now and it's pretty much ready to start.

E60: Engine Swap Week - Day 4

Had a lost day yesterday when the engine didn't arrive. It only turned up at 1.30pm today, so I will have to concentrate on swapping over the high-pressure pump, flywheel and clutch, as well as removing the loom etc. ready to patch mine in. Lifting the engine in will have to wait until tomorrow.

• Replace steering-rack / subframe bolts entirely.
• Remove loom and vacuum-hoses from new engine.
• Swap over high-pressure fuel-pump.
• Fit flywheel and clutch.
• Remove oil filter/cooler and rocker-cover for lifting.
• Match engines entirely.
• Lift engine in.

Engine arrived at 1.30pm.

And was finally sat in the bay at 7.30pm.

E60: Engine Swap Week - Day 3

• Drop prop-shaft.
• Remove slave-cyl. / gearshift linkages.
• Drop gearbox.
• Lift engine out.
• Remove parts for new engine.

Once the prop was down it didn't take long at all to get the engine out. The gearbox is huge, but surprisingly light.

Prep for new engine:

• Remove clutch.
• Remove flywheel.

Got the clutch off easy enough, but need a T55 Torx socket to remove the flywheel so that will have to wait until I get it from work tomorrow.

NOTE: Missing bolt from exhaust cross-member.